This allows CGo code to call some libc functions. Additionally, by
putting memset/memmove/memcpy in an archive they're not included anymore
when not necessary, reducing code size for small programs.
With this change, it's no longer necessary to set a specific pin mode:
it will get autodetected in the Configure() call.
Tested on an ItsyBitsy M4 with the mpu6050 example in the drivers repo.
A small footnote in the datasheet says that interrupt source numbers
correspond to the bit position in INTFLAG. We only need the RXC
interrupt for UART. In other words, ony the _2 interrupts (RXC is in the
2nd bit position) needs to be used for UART to work correctly.
In the future, more interrupts may be needed. They can then be added as
necessary.
I2C uses a hardcoded peripheral instead of referring to a specific
peripheral. In addition to that, it refers to the wrong SERCOM
(SERCOM3), which isn't used on any of the atsamd51 boards for I2C.
This commit lets the compiler know about interrupts and allows
optimizations to be performed based on that: interrupts are eliminated
when they appear to be unused in a program. This is done with a new
pseudo-call (runtime/interrupt.New) that is treated specially by the
compiler.
This greatly cuts down on compile time (by about 5x for small programs)
and also makes the program a whole lot smaller. Overall it cuts down
`make smoke-test` in the drivers repository by half (from 160s to 80s).
This will probably also fix the timeout issue in the Playground:
https://github.com/tinygo-org/playground/issues/7
This commit does the same thing as
https://github.com/tinygo-org/tinygo/pull/597 but for samd51 series
chips. Pin mode and pad numbers are automatically calculated from pin
numbers, returning an error if no valid pinout is possible.
This can be useful for debugging critical bugs in code. I haven't added
human-readable exceptions (such as "illegal instruction" or "stack
overflow") yet, they can be added when they happen in practice (to avoid
increasing code size too much).
This commit adds support for timer interrupts, replacing the busy loop
that was used before. It is perhaps the most simple interrupt to
implement and should serve as the basis for further interrupt support in
RISC-V.
The CLINT is implemented both on the fe310-g002 chip and in the sifive_e
QEMU machine type. Therefore, use that peripheral for consistency.
The only difference is the clock speed, which runs at 10MHz in QEMU for
some reason instead of 32.768kHz as on the physical HiFive1 boards.
Add a target for the Adafruit Circuit Playground Bluefruit, which is
based on the nRF52840. Adds the necessary code for the machine
package and the json and linker script files in the targets directory.
The machine package code is based on board_circuitplay_express.go,
with modifications made by consulting the wiring diagram on the
adafruit website here:
https://learn.adafruit.com/adafruit-circuit-playground-bluefruit/downloads
Also adds support to the uf2 conversion packacge to set the familyID
field. The Circuit Playground Bluefruit firmware rejects uf2 files
without the family id set to 0xADA52840 (and without the flag specifying
that the family id is present).
UART2 was configured with the wrong SERCOM for the used pins (PB22 and
PB23). However, after changing the SERCOM from 3 to 5 that led to a
conflict with UART1 (used for the on-board WiFi). But the used pins are
also usable from SERCOM 3, so in the end I switched SERCOM5 and SERCOM3
around.
With this change, I was able to get examples/echo working.
QEMU doesn't support the RTC peripheral yet so work around it for now.
This makes the following command work:
tinygo run -target=hifive1-qemu ./testdata/coroutines.go
These all-caps constants aren't in the Go style, so rename it to
CPUFrequency (which is more aligned with Go style). Additionally, make
it a function so that it is possible to add support for changing the
frequency in the future.
Tested by running `make smoketest`. None of the outputs did change.
This should make it more maintainable. Another big advantage that
generation time (including gofmt) is now 3 times faster. No real attempt
at refactoring has been made, that will need to be done at a later time.
The Cortex-M architecture contains two stack pointers, designed to be
used by RTOSes: MSP and PSP (where MSP is the default at reset). In
fact, the ARM documentation recommends using the PSP for tasks in a
RTOS.
This commit switches to using the PSP for goroutine stacks. Aside from
being the recommended operation, this has the big advantage that the
NVIC automatically switches to the MSP when handling interrupts. This
avoids having to make every goroutine stack big enough that interrupts
can be handled on it.
Additionally, I've optimized the assembly code to save/restore registers
(made possible by this change). For Cortex-M3 and up, saving all
registers is just a single push instruction and restoring+branching is a
single pop instruction. For Cortex-M0 it's a bit more work because the
push/pop instructions there don't support most high registers.
Sidenote: the fact that you can pop a number of registers and branch at
the same time makes ARM not exactly a true RISC system. However, it's
very useful in this case.
This function adjusts the time returned by time.Now() and similar
functions. This is necessary on bare metal systems, where there would
not be a way to adjust the time otherwise.
