e17a2e6776
A small footnote in the datasheet says that interrupt source numbers correspond to the bit position in INTFLAG. We only need the RXC interrupt for UART. In other words, ony the _2 interrupts (RXC is in the 2nd bit position) needs to be used for UART to work correctly. In the future, more interrupts may be needed. They can then be added as necessary.
2130 строки
63 КиБ
Go
2130 строки
63 КиБ
Go
// +build sam,atsamd51
|
|
|
|
// Peripheral abstraction layer for the atsamd51.
|
|
//
|
|
// Datasheet:
|
|
// http://ww1.microchip.com/downloads/en/DeviceDoc/60001507C.pdf
|
|
//
|
|
package machine
|
|
|
|
import (
|
|
"device/arm"
|
|
"device/sam"
|
|
"errors"
|
|
"runtime/interrupt"
|
|
"unsafe"
|
|
)
|
|
|
|
func CPUFrequency() uint32 {
|
|
return 120000000
|
|
}
|
|
|
|
type PinMode uint8
|
|
|
|
const (
|
|
PinAnalog PinMode = 1
|
|
PinSERCOM PinMode = 2
|
|
PinSERCOMAlt PinMode = 3
|
|
PinTimer PinMode = 4
|
|
PinTimerAlt PinMode = 5
|
|
PinTCCPDEC PinMode = 6
|
|
PinCom PinMode = 7
|
|
PinSDHC PinMode = 8
|
|
PinI2S PinMode = 9
|
|
PinPCC PinMode = 10
|
|
PinGMAC PinMode = 11
|
|
PinACCLK PinMode = 12
|
|
PinCCL PinMode = 13
|
|
PinDigital PinMode = 14
|
|
PinInput PinMode = 15
|
|
PinInputPullup PinMode = 16
|
|
PinOutput PinMode = 17
|
|
PinPWME PinMode = PinTimer
|
|
PinPWMF PinMode = PinTimerAlt
|
|
PinPWMG PinMode = PinTCCPDEC
|
|
PinInputPulldown PinMode = 18
|
|
)
|
|
|
|
// Hardware pins
|
|
const (
|
|
PA00 Pin = 0
|
|
PA01 Pin = 1
|
|
PA02 Pin = 2
|
|
PA03 Pin = 3
|
|
PA04 Pin = 4
|
|
PA05 Pin = 5
|
|
PA06 Pin = 6
|
|
PA07 Pin = 7
|
|
PA08 Pin = 8
|
|
PA09 Pin = 9
|
|
PA10 Pin = 10
|
|
PA11 Pin = 11
|
|
PA12 Pin = 12
|
|
PA13 Pin = 13
|
|
PA14 Pin = 14
|
|
PA15 Pin = 15
|
|
PA16 Pin = 16
|
|
PA17 Pin = 17
|
|
PA18 Pin = 18
|
|
PA19 Pin = 19
|
|
PA20 Pin = 20
|
|
PA21 Pin = 21
|
|
PA22 Pin = 22
|
|
PA23 Pin = 23
|
|
PA24 Pin = 24
|
|
PA25 Pin = 25
|
|
PA26 Pin = 26
|
|
PA27 Pin = 27
|
|
PA28 Pin = 28
|
|
PA29 Pin = 29
|
|
PA30 Pin = 30
|
|
PA31 Pin = 31
|
|
PB00 Pin = 32
|
|
PB01 Pin = 33
|
|
PB02 Pin = 34
|
|
PB03 Pin = 35
|
|
PB04 Pin = 36
|
|
PB05 Pin = 37
|
|
PB06 Pin = 38
|
|
PB07 Pin = 39
|
|
PB08 Pin = 40
|
|
PB09 Pin = 41
|
|
PB10 Pin = 42
|
|
PB11 Pin = 43
|
|
PB12 Pin = 44
|
|
PB13 Pin = 45
|
|
PB14 Pin = 46
|
|
PB15 Pin = 47
|
|
PB16 Pin = 48
|
|
PB17 Pin = 49
|
|
PB18 Pin = 50
|
|
PB19 Pin = 51
|
|
PB20 Pin = 52
|
|
PB21 Pin = 53
|
|
PB22 Pin = 54
|
|
PB23 Pin = 55
|
|
PB24 Pin = 56
|
|
PB25 Pin = 57
|
|
PB26 Pin = 58
|
|
PB27 Pin = 59
|
|
PB28 Pin = 60
|
|
PB29 Pin = 61
|
|
PB30 Pin = 62
|
|
PB31 Pin = 63
|
|
)
|
|
|
|
const (
|
|
pinPadMapSERCOM0Pad0 uint16 = 0x1000
|
|
pinPadMapSERCOM1Pad0 uint16 = 0x2000
|
|
pinPadMapSERCOM2Pad0 uint16 = 0x3000
|
|
pinPadMapSERCOM3Pad0 uint16 = 0x4000
|
|
pinPadMapSERCOM4Pad0 uint16 = 0x5000
|
|
pinPadMapSERCOM5Pad0 uint16 = 0x6000
|
|
pinPadMapSERCOM6Pad0 uint16 = 0x7000
|
|
pinPadMapSERCOM7Pad0 uint16 = 0x8000
|
|
pinPadMapSERCOM0Pad2 uint16 = 0x1200
|
|
pinPadMapSERCOM1Pad2 uint16 = 0x2200
|
|
pinPadMapSERCOM2Pad2 uint16 = 0x3200
|
|
pinPadMapSERCOM3Pad2 uint16 = 0x4200
|
|
pinPadMapSERCOM4Pad2 uint16 = 0x5200
|
|
pinPadMapSERCOM5Pad2 uint16 = 0x6200
|
|
pinPadMapSERCOM6Pad2 uint16 = 0x7200
|
|
pinPadMapSERCOM7Pad2 uint16 = 0x8200
|
|
|
|
pinPadMapSERCOM0AltPad0 uint16 = 0x0010
|
|
pinPadMapSERCOM1AltPad0 uint16 = 0x0020
|
|
pinPadMapSERCOM2AltPad0 uint16 = 0x0030
|
|
pinPadMapSERCOM3AltPad0 uint16 = 0x0040
|
|
pinPadMapSERCOM4AltPad0 uint16 = 0x0050
|
|
pinPadMapSERCOM5AltPad0 uint16 = 0x0060
|
|
pinPadMapSERCOM6AltPad0 uint16 = 0x0070
|
|
pinPadMapSERCOM7AltPad0 uint16 = 0x0080
|
|
pinPadMapSERCOM0AltPad1 uint16 = 0x0011
|
|
pinPadMapSERCOM1AltPad1 uint16 = 0x0021
|
|
pinPadMapSERCOM2AltPad1 uint16 = 0x0031
|
|
pinPadMapSERCOM3AltPad1 uint16 = 0x0041
|
|
pinPadMapSERCOM4AltPad1 uint16 = 0x0051
|
|
pinPadMapSERCOM5AltPad1 uint16 = 0x0061
|
|
pinPadMapSERCOM6AltPad1 uint16 = 0x0071
|
|
pinPadMapSERCOM7AltPad1 uint16 = 0x0081
|
|
pinPadMapSERCOM0AltPad2 uint16 = 0x0012
|
|
pinPadMapSERCOM1AltPad2 uint16 = 0x0022
|
|
pinPadMapSERCOM2AltPad2 uint16 = 0x0032
|
|
pinPadMapSERCOM3AltPad2 uint16 = 0x0042
|
|
pinPadMapSERCOM4AltPad2 uint16 = 0x0052
|
|
pinPadMapSERCOM5AltPad2 uint16 = 0x0062
|
|
pinPadMapSERCOM6AltPad2 uint16 = 0x0072
|
|
pinPadMapSERCOM7AltPad2 uint16 = 0x0082
|
|
)
|
|
|
|
// pinPadMapping lists which pins have which SERCOMs attached to them.
|
|
// The encoding is rather dense, with each uint16 encoding two pins and both
|
|
// SERCOM and SERCOM-ALT.
|
|
//
|
|
// Observations:
|
|
// * There are eight SERCOMs. Those SERCOM numbers can be encoded in 4 bits.
|
|
// * Even pad numbers are usually on even pins, and odd pad numbers are usually
|
|
// on odd pins. The exception is SERCOM-ALT, which sometimes swaps pad 0 and 1.
|
|
// With that, there is still an invariant that the pad number for an odd pin is
|
|
// the pad number for the corresponding even pin with the low bit toggled.
|
|
// * Pin pads come in pairs. If PA00 has pad 0, then PA01 has pad 1.
|
|
// With this information, we can encode SERCOM pin/pad numbers much more
|
|
// efficiently. Due to pads coming in pairs, we can ignore half the pins: the
|
|
// information for an odd pin can be calculated easily from the preceding even
|
|
// pin.
|
|
//
|
|
// Each word below is split in two bytes. The 8 high bytes are for SERCOM and
|
|
// the 8 low bits are for SERCOM-ALT. Of each byte, the 4 high bits encode the
|
|
// SERCOM + 1 while the two low bits encodes the pad number (the pad number for
|
|
// the odd pin can be trivially calculated by toggling the low bit of the pad
|
|
// number). It encodes SERCOM + 1 instead of just the SERCOM number, to make it
|
|
// easy to check whether a nibble is set at all.
|
|
//
|
|
// Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/60001507E.pdf
|
|
var pinPadMapping = [32]uint16{
|
|
// page 32
|
|
PA00 / 2: 0 | pinPadMapSERCOM1AltPad0,
|
|
|
|
// page 33
|
|
PB08 / 2: 0 | pinPadMapSERCOM4AltPad0,
|
|
PA04 / 2: 0 | pinPadMapSERCOM0AltPad0,
|
|
PA06 / 2: 0 | pinPadMapSERCOM0AltPad2,
|
|
//PC04 / 2: pinPadMapSERCOM6Pad0 | 0,
|
|
//PC06 / 2: pinPadMapSERCOM6Pad2 | 0,
|
|
PA08 / 2: pinPadMapSERCOM0Pad0 | pinPadMapSERCOM2AltPad1,
|
|
PA10 / 2: pinPadMapSERCOM0Pad2 | pinPadMapSERCOM2AltPad2,
|
|
PB10 / 2: 0 | pinPadMapSERCOM4AltPad2,
|
|
PB12 / 2: pinPadMapSERCOM4Pad0 | 0,
|
|
PB14 / 2: pinPadMapSERCOM4Pad2 | 0,
|
|
//PD08 / 2: pinPadMapSERCOM7Pad0 | pinPadMapSERCOM6AltPad1,
|
|
//PD10 / 2: pinPadMapSERCOM7Pad2 | pinPadMapSERCOM6AltPad2,
|
|
//PC10 / 2: pinPadMapSERCOM6Pad2 | pinPadMapSERCOM7AltPad2,
|
|
|
|
// page 34
|
|
//PC12 / 2: pinPadMapSERCOM7Pad0 | pinPadMapSERCOM6AltPad1,
|
|
//PC14 / 2: pinPadMapSERCOM7Pad2 | pinPadMapSERCOM6AltPad2,
|
|
PA12 / 2: pinPadMapSERCOM2Pad0 | pinPadMapSERCOM4AltPad1,
|
|
PA14 / 2: pinPadMapSERCOM2Pad2 | pinPadMapSERCOM4AltPad2,
|
|
PA16 / 2: pinPadMapSERCOM1Pad0 | pinPadMapSERCOM3AltPad1,
|
|
PA18 / 2: pinPadMapSERCOM1Pad2 | pinPadMapSERCOM3AltPad2,
|
|
//PC16 / 2: pinPadMapSERCOM6Pad0 | pinPadMapSERCOM0AltPad1,
|
|
//PC18 / 2: pinPadMapSERCOM6Pad2 | pinPadMapSERCOM0AltPad2,
|
|
//PC22 / 2: pinPadMapSERCOM1Pad0 | pinPadMapSERCOM3AltPad1,
|
|
//PD20 / 2: pinPadMapSERCOM1Pad2 | pinPadMapSERCOM3AltPad2,
|
|
PB16 / 2: pinPadMapSERCOM5Pad0 | 0,
|
|
PB18 / 2: pinPadMapSERCOM5Pad2 | pinPadMapSERCOM7AltPad2,
|
|
|
|
// page 35
|
|
PB20 / 2: pinPadMapSERCOM3Pad0 | pinPadMapSERCOM7AltPad1,
|
|
PA20 / 2: pinPadMapSERCOM5Pad2 | pinPadMapSERCOM3AltPad2,
|
|
PA22 / 2: pinPadMapSERCOM3Pad0 | pinPadMapSERCOM5AltPad1,
|
|
PA24 / 2: pinPadMapSERCOM3Pad2 | pinPadMapSERCOM5AltPad2,
|
|
PB22 / 2: pinPadMapSERCOM1Pad2 | pinPadMapSERCOM5AltPad2,
|
|
PB24 / 2: pinPadMapSERCOM0Pad0 | pinPadMapSERCOM2AltPad1,
|
|
PB26 / 2: pinPadMapSERCOM2Pad0 | pinPadMapSERCOM4AltPad1,
|
|
PB28 / 2: pinPadMapSERCOM2Pad2 | pinPadMapSERCOM4AltPad2,
|
|
//PC24 / 2: pinPadMapSERCOM0Pad2 | pinPadMapSERCOM2AltPad2,
|
|
//PC26 / 2: pinPadMapSERCOM1Pad1 | 0, // note: PC26 doesn't support SERCOM, but PC27 does
|
|
//PC28 / 2: pinPadMapSERCOM1Pad1 | 0, // note: PC29 doesn't exist in the datasheet?
|
|
PA30 / 2: 0 | pinPadMapSERCOM1AltPad2,
|
|
|
|
// page 36
|
|
PB30 / 2: 0 | pinPadMapSERCOM5AltPad1,
|
|
PB00 / 2: 0 | pinPadMapSERCOM5AltPad2,
|
|
PB02 / 2: 0 | pinPadMapSERCOM5AltPad0,
|
|
}
|
|
|
|
// findPinPadMapping looks up the pad number and the pinmode for a given pin and
|
|
// SERCOM number. The result can either be SERCOM, SERCOM-ALT, or "not found"
|
|
// (indicated by returning ok=false). The pad number is returned to calculate
|
|
// the DOPO/DIPO bitfields of the various serial peripherals.
|
|
func findPinPadMapping(sercom uint8, pin Pin) (pinMode PinMode, pad uint32, ok bool) {
|
|
bytes := pinPadMapping[pin/2]
|
|
upper := byte(bytes >> 8)
|
|
lower := byte(bytes & 0xff)
|
|
|
|
if upper != 0 {
|
|
// SERCOM
|
|
if (upper>>4)-1 == sercom {
|
|
pinMode = PinSERCOM
|
|
pad |= uint32(upper % 4)
|
|
ok = true
|
|
}
|
|
}
|
|
if lower != 0 {
|
|
// SERCOM-ALT
|
|
if (lower>>4)-1 == sercom {
|
|
pinMode = PinSERCOMAlt
|
|
pad |= uint32(lower % 4)
|
|
ok = true
|
|
}
|
|
}
|
|
|
|
if ok {
|
|
// If the pin is uneven, toggle the lowest bit of the pad number.
|
|
if pin&1 != 0 {
|
|
pad ^= 1
|
|
}
|
|
}
|
|
return
|
|
}
|
|
|
|
// Return the register and mask to enable a given GPIO pin. This can be used to
|
|
// implement bit-banged drivers.
|
|
func (p Pin) PortMaskSet() (*uint32, uint32) {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
return &sam.PORT.GROUP[group].OUTSET.Reg, 1 << pin_in_group
|
|
}
|
|
|
|
// Return the register and mask to disable a given port. This can be used to
|
|
// implement bit-banged drivers.
|
|
func (p Pin) PortMaskClear() (*uint32, uint32) {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
return &sam.PORT.GROUP[group].OUTCLR.Reg, 1 << pin_in_group
|
|
}
|
|
|
|
// Set the pin to high or low.
|
|
// Warning: only use this on an output pin!
|
|
func (p Pin) Set(high bool) {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
if high {
|
|
sam.PORT.GROUP[group].OUTSET.Set(1 << pin_in_group)
|
|
} else {
|
|
sam.PORT.GROUP[group].OUTCLR.Set(1 << pin_in_group)
|
|
}
|
|
}
|
|
|
|
// Get returns the current value of a GPIO pin.
|
|
func (p Pin) Get() bool {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
return (sam.PORT.GROUP[group].IN.Get()>>pin_in_group)&1 > 0
|
|
}
|
|
|
|
// Toggle switches an output pin from low to high or from high to low.
|
|
// Warning: only use this on an output pin!
|
|
func (p Pin) Toggle() {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
sam.PORT.GROUP[group].OUTTGL.Set(1 << pin_in_group)
|
|
}
|
|
|
|
// Configure this pin with the given configuration.
|
|
func (p Pin) Configure(config PinConfig) {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
switch config.Mode {
|
|
case PinOutput:
|
|
sam.PORT.GROUP[group].DIRSET.Set(1 << pin_in_group)
|
|
// output is also set to input enable so pin can read back its own value
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_INEN)
|
|
|
|
case PinInput:
|
|
sam.PORT.GROUP[group].DIRCLR.Set(1 << pin_in_group)
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_INEN)
|
|
|
|
case PinInputPulldown:
|
|
sam.PORT.GROUP[group].DIRCLR.Set(1 << pin_in_group)
|
|
sam.PORT.GROUP[group].OUTCLR.Set(1 << pin_in_group)
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_INEN | sam.PORT_GROUP_PINCFG_PULLEN)
|
|
|
|
case PinInputPullup:
|
|
sam.PORT.GROUP[group].DIRCLR.Set(1 << pin_in_group)
|
|
sam.PORT.GROUP[group].OUTSET.Set(1 << pin_in_group)
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_INEN | sam.PORT_GROUP_PINCFG_PULLEN)
|
|
|
|
case PinSERCOM:
|
|
if p&1 > 0 {
|
|
// odd pin, so save the even pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXE_Msk
|
|
p.setPMux(val | (uint8(PinSERCOM) << sam.PORT_GROUP_PMUX_PMUXO_Pos))
|
|
} else {
|
|
// even pin, so save the odd pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXO_Msk
|
|
p.setPMux(val | (uint8(PinSERCOM) << sam.PORT_GROUP_PMUX_PMUXE_Pos))
|
|
}
|
|
// enable port config
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_PMUXEN | sam.PORT_GROUP_PINCFG_DRVSTR | sam.PORT_GROUP_PINCFG_INEN)
|
|
|
|
case PinSERCOMAlt:
|
|
if p&1 > 0 {
|
|
// odd pin, so save the even pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXE_Msk
|
|
p.setPMux(val | (uint8(PinSERCOMAlt) << sam.PORT_GROUP_PMUX_PMUXO_Pos))
|
|
} else {
|
|
// even pin, so save the odd pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXO_Msk
|
|
p.setPMux(val | (uint8(PinSERCOMAlt) << sam.PORT_GROUP_PMUX_PMUXE_Pos))
|
|
}
|
|
// enable port config
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_PMUXEN | sam.PORT_GROUP_PINCFG_DRVSTR)
|
|
|
|
case PinCom:
|
|
if p&1 > 0 {
|
|
// odd pin, so save the even pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXE_Msk
|
|
p.setPMux(val | (uint8(PinCom) << sam.PORT_GROUP_PMUX_PMUXO_Pos))
|
|
} else {
|
|
// even pin, so save the odd pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXO_Msk
|
|
p.setPMux(val | (uint8(PinCom) << sam.PORT_GROUP_PMUX_PMUXE_Pos))
|
|
}
|
|
// enable port config
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_PMUXEN)
|
|
case PinAnalog:
|
|
if p&1 > 0 {
|
|
// odd pin, so save the even pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXE_Msk
|
|
p.setPMux(val | (uint8(PinAnalog) << sam.PORT_GROUP_PMUX_PMUXO_Pos))
|
|
} else {
|
|
// even pin, so save the odd pins
|
|
val := p.getPMux() & sam.PORT_GROUP_PMUX_PMUXO_Msk
|
|
p.setPMux(val | (uint8(PinAnalog) << sam.PORT_GROUP_PMUX_PMUXE_Pos))
|
|
}
|
|
// enable port config
|
|
p.setPinCfg(sam.PORT_GROUP_PINCFG_PMUXEN | sam.PORT_GROUP_PINCFG_DRVSTR)
|
|
}
|
|
}
|
|
|
|
// getPMux returns the value for the correct PMUX register for this pin.
|
|
func (p Pin) getPMux() uint8 {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
return sam.PORT.GROUP[group].PMUX[pin_in_group>>1].Get()
|
|
}
|
|
|
|
// setPMux sets the value for the correct PMUX register for this pin.
|
|
func (p Pin) setPMux(val uint8) {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
sam.PORT.GROUP[group].PMUX[pin_in_group>>1].Set(val)
|
|
}
|
|
|
|
// getPinCfg returns the value for the correct PINCFG register for this pin.
|
|
func (p Pin) getPinCfg() uint8 {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
return sam.PORT.GROUP[group].PINCFG[pin_in_group].Get()
|
|
}
|
|
|
|
// setPinCfg sets the value for the correct PINCFG register for this pin.
|
|
func (p Pin) setPinCfg(val uint8) {
|
|
group, pin_in_group := p.getPinGrouping()
|
|
sam.PORT.GROUP[group].PINCFG[pin_in_group].Set(val)
|
|
}
|
|
|
|
// getPinGrouping calculates the gpio group and pin id from the pin number.
|
|
// Pins are split into groups of 32, and each group has its own set of
|
|
// control registers.
|
|
func (p Pin) getPinGrouping() (uint8, uint8) {
|
|
group := uint8(p) >> 5
|
|
pin_in_group := uint8(p) & 0x1f
|
|
return group, pin_in_group
|
|
}
|
|
|
|
// InitADC initializes the ADC.
|
|
func InitADC() {
|
|
// ADC Bias Calibration
|
|
// NVMCTRL_SW0 0x00800080
|
|
// #define ADC0_FUSES_BIASCOMP_ADDR NVMCTRL_SW0
|
|
// #define ADC0_FUSES_BIASCOMP_Pos 2 /**< \brief (NVMCTRL_SW0) ADC Comparator Scaling */
|
|
// #define ADC0_FUSES_BIASCOMP_Msk (_Ul(0x7) << ADC0_FUSES_BIASCOMP_Pos)
|
|
// #define ADC0_FUSES_BIASCOMP(value) (ADC0_FUSES_BIASCOMP_Msk & ((value) << ADC0_FUSES_BIASCOMP_Pos))
|
|
|
|
// #define ADC0_FUSES_BIASR2R_ADDR NVMCTRL_SW0
|
|
// #define ADC0_FUSES_BIASR2R_Pos 8 /**< \brief (NVMCTRL_SW0) ADC Bias R2R ampli scaling */
|
|
// #define ADC0_FUSES_BIASR2R_Msk (_Ul(0x7) << ADC0_FUSES_BIASR2R_Pos)
|
|
// #define ADC0_FUSES_BIASR2R(value) (ADC0_FUSES_BIASR2R_Msk & ((value) << ADC0_FUSES_BIASR2R_Pos))
|
|
|
|
// #define ADC0_FUSES_BIASREFBUF_ADDR NVMCTRL_SW0
|
|
// #define ADC0_FUSES_BIASREFBUF_Pos 5 /**< \brief (NVMCTRL_SW0) ADC Bias Reference Buffer Scaling */
|
|
// #define ADC0_FUSES_BIASREFBUF_Msk (_Ul(0x7) << ADC0_FUSES_BIASREFBUF_Pos)
|
|
// #define ADC0_FUSES_BIASREFBUF(value) (ADC0_FUSES_BIASREFBUF_Msk & ((value) << ADC0_FUSES_BIASREFBUF_Pos))
|
|
|
|
// #define ADC1_FUSES_BIASCOMP_ADDR NVMCTRL_SW0
|
|
// #define ADC1_FUSES_BIASCOMP_Pos 16 /**< \brief (NVMCTRL_SW0) ADC Comparator Scaling */
|
|
// #define ADC1_FUSES_BIASCOMP_Msk (_Ul(0x7) << ADC1_FUSES_BIASCOMP_Pos)
|
|
// #define ADC1_FUSES_BIASCOMP(value) (ADC1_FUSES_BIASCOMP_Msk & ((value) << ADC1_FUSES_BIASCOMP_Pos))
|
|
|
|
// #define ADC1_FUSES_BIASR2R_ADDR NVMCTRL_SW0
|
|
// #define ADC1_FUSES_BIASR2R_Pos 22 /**< \brief (NVMCTRL_SW0) ADC Bias R2R ampli scaling */
|
|
// #define ADC1_FUSES_BIASR2R_Msk (_Ul(0x7) << ADC1_FUSES_BIASR2R_Pos)
|
|
// #define ADC1_FUSES_BIASR2R(value) (ADC1_FUSES_BIASR2R_Msk & ((value) << ADC1_FUSES_BIASR2R_Pos))
|
|
|
|
// #define ADC1_FUSES_BIASREFBUF_ADDR NVMCTRL_SW0
|
|
// #define ADC1_FUSES_BIASREFBUF_Pos 19 /**< \brief (NVMCTRL_SW0) ADC Bias Reference Buffer Scaling */
|
|
// #define ADC1_FUSES_BIASREFBUF_Msk (_Ul(0x7) << ADC1_FUSES_BIASREFBUF_Pos)
|
|
// #define ADC1_FUSES_BIASREFBUF(value) (ADC1_FUSES_BIASREFBUF_Msk & ((value) << ADC1_FUSES_BIASREFBUF_Pos))
|
|
|
|
adcFuse := *(*uint32)(unsafe.Pointer(uintptr(0x00800080)))
|
|
|
|
// uint32_t biascomp = (*((uint32_t *)ADC0_FUSES_BIASCOMP_ADDR) & ADC0_FUSES_BIASCOMP_Msk) >> ADC0_FUSES_BIASCOMP_Pos;
|
|
biascomp := (adcFuse & uint32(0x7<<2)) //>> 2
|
|
|
|
// uint32_t biasr2r = (*((uint32_t *)ADC0_FUSES_BIASR2R_ADDR) & ADC0_FUSES_BIASR2R_Msk) >> ADC0_FUSES_BIASR2R_Pos;
|
|
biasr2r := (adcFuse & uint32(0x7<<8)) //>> 8
|
|
|
|
// uint32_t biasref = (*((uint32_t *)ADC0_FUSES_BIASREFBUF_ADDR) & ADC0_FUSES_BIASREFBUF_Msk) >> ADC0_FUSES_BIASREFBUF_Pos;
|
|
biasref := (adcFuse & uint32(0x7<<5)) //>> 5
|
|
|
|
// calibrate ADC0
|
|
sam.ADC0.CALIB.Set(uint16(biascomp | biasr2r | biasref))
|
|
|
|
// biascomp = (*((uint32_t *)ADC1_FUSES_BIASCOMP_ADDR) & ADC1_FUSES_BIASCOMP_Msk) >> ADC1_FUSES_BIASCOMP_Pos;
|
|
biascomp = (adcFuse & uint32(0x7<<16)) //>> 16
|
|
|
|
// biasr2r = (*((uint32_t *)ADC1_FUSES_BIASR2R_ADDR) & ADC1_FUSES_BIASR2R_Msk) >> ADC1_FUSES_BIASR2R_Pos;
|
|
biasr2r = (adcFuse & uint32(0x7<<22)) //>> 22
|
|
|
|
// biasref = (*((uint32_t *)ADC1_FUSES_BIASREFBUF_ADDR) & ADC1_FUSES_BIASREFBUF_Msk) >> ADC1_FUSES_BIASREFBUF_Pos;
|
|
biasref = (adcFuse & uint32(0x7<<19)) //>> 19
|
|
|
|
// calibrate ADC1
|
|
sam.ADC1.CALIB.Set(uint16((biascomp | biasr2r | biasref) >> 16))
|
|
|
|
sam.ADC0.CTRLA.SetBits(sam.ADC_CTRLA_PRESCALER_DIV32 << sam.ADC_CTRLA_PRESCALER_Pos)
|
|
// adcs[i]->CTRLB.bit.RESSEL = ADC_CTRLB_RESSEL_10BIT_Val;
|
|
sam.ADC0.CTRLB.SetBits(sam.ADC_CTRLB_RESSEL_12BIT << sam.ADC_CTRLB_RESSEL_Pos)
|
|
|
|
// wait for sync
|
|
for sam.ADC0.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_CTRLB) {
|
|
}
|
|
|
|
// sampling Time Length
|
|
sam.ADC0.SAMPCTRL.Set(5)
|
|
|
|
// wait for sync
|
|
for sam.ADC0.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_SAMPCTRL) {
|
|
}
|
|
|
|
// No Negative input (Internal Ground)
|
|
sam.ADC0.INPUTCTRL.Set(sam.ADC_INPUTCTRL_MUXNEG_GND << sam.ADC_INPUTCTRL_MUXNEG_Pos)
|
|
|
|
// wait for sync
|
|
for sam.ADC0.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_INPUTCTRL) {
|
|
}
|
|
|
|
// Averaging (see datasheet table in AVGCTRL register description)
|
|
// 1 sample only (no oversampling nor averaging), adjusting result by 0
|
|
sam.ADC0.AVGCTRL.Set(sam.ADC_AVGCTRL_SAMPLENUM_1 | (0 << sam.ADC_AVGCTRL_ADJRES_Pos))
|
|
|
|
// wait for sync
|
|
for sam.ADC0.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_AVGCTRL) {
|
|
}
|
|
|
|
// same for ADC1, as for ADC0
|
|
sam.ADC1.CTRLA.SetBits(sam.ADC_CTRLA_PRESCALER_DIV32 << sam.ADC_CTRLA_PRESCALER_Pos)
|
|
sam.ADC1.CTRLB.SetBits(sam.ADC_CTRLB_RESSEL_12BIT << sam.ADC_CTRLB_RESSEL_Pos)
|
|
for sam.ADC1.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_CTRLB) {
|
|
}
|
|
sam.ADC1.SAMPCTRL.Set(5)
|
|
for sam.ADC1.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_SAMPCTRL) {
|
|
}
|
|
sam.ADC1.INPUTCTRL.Set(sam.ADC_INPUTCTRL_MUXNEG_GND << sam.ADC_INPUTCTRL_MUXNEG_Pos)
|
|
for sam.ADC1.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_INPUTCTRL) {
|
|
}
|
|
sam.ADC1.AVGCTRL.Set(sam.ADC_AVGCTRL_SAMPLENUM_1 | (0 << sam.ADC_AVGCTRL_ADJRES_Pos))
|
|
for sam.ADC1.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_AVGCTRL) {
|
|
}
|
|
|
|
// wait for sync
|
|
for sam.ADC0.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_REFCTRL) {
|
|
}
|
|
for sam.ADC1.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_REFCTRL) {
|
|
}
|
|
|
|
// default is 3V3 reference voltage
|
|
sam.ADC0.REFCTRL.SetBits(sam.ADC_REFCTRL_REFSEL_INTVCC1)
|
|
sam.ADC1.REFCTRL.SetBits(sam.ADC_REFCTRL_REFSEL_INTVCC1)
|
|
}
|
|
|
|
// Configure configures a ADCPin to be able to be used to read data.
|
|
func (a ADC) Configure() {
|
|
a.Pin.Configure(PinConfig{Mode: PinAnalog})
|
|
}
|
|
|
|
// Get returns the current value of a ADC pin, in the range 0..0xffff.
|
|
func (a ADC) Get() uint16 {
|
|
bus := a.getADCBus()
|
|
ch := a.getADCChannel()
|
|
|
|
for bus.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_INPUTCTRL) {
|
|
}
|
|
|
|
// Selection for the positive ADC input channel
|
|
bus.INPUTCTRL.ClearBits(sam.ADC_INPUTCTRL_MUXPOS_Msk)
|
|
for bus.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_ENABLE) {
|
|
}
|
|
bus.INPUTCTRL.SetBits((uint16(ch) & sam.ADC_INPUTCTRL_MUXPOS_Msk) << sam.ADC_INPUTCTRL_MUXPOS_Pos)
|
|
for bus.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
// Enable ADC
|
|
bus.CTRLA.SetBits(sam.ADC_CTRLA_ENABLE)
|
|
for bus.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
// Start conversion
|
|
bus.SWTRIG.SetBits(sam.ADC_SWTRIG_START)
|
|
for !bus.INTFLAG.HasBits(sam.ADC_INTFLAG_RESRDY) {
|
|
}
|
|
|
|
// Clear the Data Ready flag
|
|
bus.INTFLAG.ClearBits(sam.ADC_INTFLAG_RESRDY)
|
|
for bus.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
// Start conversion again, since first conversion after reference voltage changed is invalid.
|
|
bus.SWTRIG.SetBits(sam.ADC_SWTRIG_START)
|
|
|
|
// Waiting for conversion to complete
|
|
for !bus.INTFLAG.HasBits(sam.ADC_INTFLAG_RESRDY) {
|
|
}
|
|
val := bus.RESULT.Get()
|
|
|
|
// Disable ADC
|
|
for bus.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_ENABLE) {
|
|
}
|
|
bus.CTRLA.ClearBits(sam.ADC_CTRLA_ENABLE)
|
|
for bus.SYNCBUSY.HasBits(sam.ADC_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
return uint16(val) << 4 // scales from 12 to 16-bit result
|
|
}
|
|
|
|
func (a ADC) getADCBus() *sam.ADC_Type {
|
|
return sam.ADC0
|
|
}
|
|
|
|
func (a ADC) getADCChannel() uint8 {
|
|
switch a.Pin {
|
|
case PA02:
|
|
return 0
|
|
case PB08:
|
|
return 2
|
|
case PB09:
|
|
return 3
|
|
case PA04:
|
|
return 4
|
|
case PA05:
|
|
return 5
|
|
case PA06:
|
|
return 6
|
|
case PA07:
|
|
return 7
|
|
case PB00:
|
|
return 12
|
|
case PB01:
|
|
return 13
|
|
case PB02:
|
|
return 14
|
|
case PB03:
|
|
return 15
|
|
case PA09:
|
|
return 17
|
|
case PA11:
|
|
return 19
|
|
default:
|
|
panic("Invalid ADC pin")
|
|
}
|
|
}
|
|
|
|
// UART on the SAMD51.
|
|
type UART struct {
|
|
Buffer *RingBuffer
|
|
Bus *sam.SERCOM_USART_INT_Type
|
|
SERCOM uint8
|
|
IRQVal uint32 // RXC interrupt
|
|
}
|
|
|
|
var (
|
|
// UART0 is actually a USB CDC interface.
|
|
UART0 = USBCDC{Buffer: NewRingBuffer()}
|
|
|
|
// The first hardware serial port on the SAMD51. Uses the SERCOM3 interface.
|
|
UART1 = UART{
|
|
Buffer: NewRingBuffer(),
|
|
Bus: sam.SERCOM3_USART_INT,
|
|
SERCOM: 3,
|
|
IRQVal: sam.IRQ_SERCOM3_2, // RXC interrupt
|
|
}
|
|
|
|
// The second hardware serial port on the SAMD51. Uses the SERCOM0 interface.
|
|
UART2 = UART{
|
|
Buffer: NewRingBuffer(),
|
|
Bus: sam.SERCOM0_USART_INT,
|
|
SERCOM: 0,
|
|
IRQVal: sam.IRQ_SERCOM0_2, // RXC interrupt
|
|
}
|
|
)
|
|
|
|
const (
|
|
sampleRate16X = 16
|
|
lsbFirst = 1
|
|
)
|
|
|
|
// Configure the UART.
|
|
func (uart UART) Configure(config UARTConfig) error {
|
|
// Default baud rate to 115200.
|
|
if config.BaudRate == 0 {
|
|
config.BaudRate = 115200
|
|
}
|
|
|
|
// determine pins
|
|
if config.TX == 0 && config.RX == 0 {
|
|
// use default pins
|
|
config.TX = UART_TX_PIN
|
|
config.RX = UART_RX_PIN
|
|
}
|
|
|
|
// Determine transmit pinout.
|
|
txPinMode, txPad, ok := findPinPadMapping(uart.SERCOM, config.TX)
|
|
if !ok {
|
|
return ErrInvalidOutputPin
|
|
}
|
|
var txPinOut uint32
|
|
// See CTRLA.RXPO bits of the SERCOM USART peripheral (page 945-946) for how
|
|
// pads are mapped to pinout values.
|
|
switch txPad {
|
|
case 0:
|
|
txPinOut = 0
|
|
default:
|
|
// TODO: flow control (RTS/CTS)
|
|
return ErrInvalidOutputPin
|
|
}
|
|
|
|
// Determine receive pinout.
|
|
rxPinMode, rxPad, ok := findPinPadMapping(uart.SERCOM, config.RX)
|
|
if !ok {
|
|
return ErrInvalidInputPin
|
|
}
|
|
// As you can see in the CTRLA.RXPO bits of the SERCOM USART peripheral
|
|
// (page 945), input pins are mapped directly.
|
|
rxPinOut := rxPad
|
|
|
|
// configure pins
|
|
config.TX.Configure(PinConfig{Mode: txPinMode})
|
|
config.RX.Configure(PinConfig{Mode: rxPinMode})
|
|
|
|
// reset SERCOM
|
|
uart.Bus.CTRLA.SetBits(sam.SERCOM_USART_INT_CTRLA_SWRST)
|
|
for uart.Bus.CTRLA.HasBits(sam.SERCOM_USART_INT_CTRLA_SWRST) ||
|
|
uart.Bus.SYNCBUSY.HasBits(sam.SERCOM_USART_INT_SYNCBUSY_SWRST) {
|
|
}
|
|
|
|
// set UART mode/sample rate
|
|
// SERCOM_USART_CTRLA_MODE(mode) |
|
|
// SERCOM_USART_CTRLA_SAMPR(sampleRate);
|
|
// sam.SERCOM_USART_CTRLA_MODE_USART_INT_CLK = 1?
|
|
uart.Bus.CTRLA.Set((1 << sam.SERCOM_USART_INT_CTRLA_MODE_Pos) |
|
|
(1 << sam.SERCOM_USART_INT_CTRLA_SAMPR_Pos)) // sample rate of 16x
|
|
|
|
// Set baud rate
|
|
uart.SetBaudRate(config.BaudRate)
|
|
|
|
// setup UART frame
|
|
// SERCOM_USART_CTRLA_FORM( (parityMode == SERCOM_NO_PARITY ? 0 : 1) ) |
|
|
// dataOrder << SERCOM_USART_CTRLA_DORD_Pos;
|
|
uart.Bus.CTRLA.SetBits((0 << sam.SERCOM_USART_INT_CTRLA_FORM_Pos) | // no parity
|
|
(lsbFirst << sam.SERCOM_USART_INT_CTRLA_DORD_Pos)) // data order
|
|
|
|
// set UART stop bits/parity
|
|
// SERCOM_USART_CTRLB_CHSIZE(charSize) |
|
|
// nbStopBits << SERCOM_USART_CTRLB_SBMODE_Pos |
|
|
// (parityMode == SERCOM_NO_PARITY ? 0 : parityMode) << SERCOM_USART_CTRLB_PMODE_Pos; //If no parity use default value
|
|
uart.Bus.CTRLB.SetBits((0 << sam.SERCOM_USART_INT_CTRLB_CHSIZE_Pos) | // 8 bits is 0
|
|
(0 << sam.SERCOM_USART_INT_CTRLB_SBMODE_Pos) | // 1 stop bit is zero
|
|
(0 << sam.SERCOM_USART_INT_CTRLB_PMODE_Pos)) // no parity
|
|
|
|
// set UART pads. This is not same as pins...
|
|
// SERCOM_USART_CTRLA_TXPO(txPad) |
|
|
// SERCOM_USART_CTRLA_RXPO(rxPad);
|
|
uart.Bus.CTRLA.SetBits((txPinOut << sam.SERCOM_USART_INT_CTRLA_TXPO_Pos) |
|
|
(rxPinOut << sam.SERCOM_USART_INT_CTRLA_RXPO_Pos))
|
|
|
|
// Enable Transceiver and Receiver
|
|
//sercom->USART.CTRLB.reg |= SERCOM_USART_CTRLB_TXEN | SERCOM_USART_CTRLB_RXEN ;
|
|
uart.Bus.CTRLB.SetBits(sam.SERCOM_USART_INT_CTRLB_TXEN | sam.SERCOM_USART_INT_CTRLB_RXEN)
|
|
|
|
// Enable USART1 port.
|
|
// sercom->USART.CTRLA.bit.ENABLE = 0x1u;
|
|
uart.Bus.CTRLA.SetBits(sam.SERCOM_USART_INT_CTRLA_ENABLE)
|
|
for uart.Bus.SYNCBUSY.HasBits(sam.SERCOM_USART_INT_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
// setup interrupt on receive
|
|
uart.Bus.INTENSET.Set(sam.SERCOM_USART_INT_INTENSET_RXC)
|
|
|
|
// Enable RX IRQ.
|
|
// This is a small note at the bottom of the NVIC section of the datasheet:
|
|
// > The integer number specified in the source refers to the respective bit
|
|
// > position in the INTFLAG register of respective peripheral.
|
|
// Therefore, if we only need to listen to the RXC interrupt source (in bit
|
|
// position 2), we only need interrupt source 2 for this SERCOM device.
|
|
arm.EnableIRQ(uart.IRQVal)
|
|
|
|
return nil
|
|
}
|
|
|
|
// SetBaudRate sets the communication speed for the UART.
|
|
func (uart UART) SetBaudRate(br uint32) {
|
|
// Asynchronous fractional mode (Table 24-2 in datasheet)
|
|
// BAUD = fref / (sampleRateValue * fbaud)
|
|
// (multiply by 8, to calculate fractional piece)
|
|
// uint32_t baudTimes8 = (SystemCoreClock * 8) / (16 * baudrate);
|
|
baud := (SERCOM_FREQ_REF * 8) / (sampleRate16X * br)
|
|
|
|
// sercom->USART.BAUD.FRAC.FP = (baudTimes8 % 8);
|
|
// sercom->USART.BAUD.FRAC.BAUD = (baudTimes8 / 8);
|
|
uart.Bus.BAUD.Set(uint16(((baud % 8) << sam.SERCOM_USART_INT_BAUD_FRAC_MODE_FP_Pos) |
|
|
((baud / 8) << sam.SERCOM_USART_INT_BAUD_FRAC_MODE_BAUD_Pos)))
|
|
}
|
|
|
|
// WriteByte writes a byte of data to the UART.
|
|
func (uart UART) WriteByte(c byte) error {
|
|
// wait until ready to receive
|
|
for !uart.Bus.INTFLAG.HasBits(sam.SERCOM_USART_INT_INTFLAG_DRE) {
|
|
}
|
|
uart.Bus.DATA.Set(uint32(c))
|
|
return nil
|
|
}
|
|
|
|
//go:export SERCOM3_2_IRQHandler
|
|
func handleSERCOM3_2() {
|
|
// should reset IRQ
|
|
UART1.Receive(byte((UART1.Bus.DATA.Get() & 0xFF)))
|
|
UART1.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
|
|
}
|
|
|
|
//go:export SERCOM0_2_IRQHandler
|
|
func handleSERCOM0_2() {
|
|
// should reset IRQ
|
|
UART2.Receive(byte((UART2.Bus.DATA.Get() & 0xFF)))
|
|
UART2.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
|
|
}
|
|
|
|
// I2C on the SAMD51.
|
|
type I2C struct {
|
|
Bus *sam.SERCOM_I2CM_Type
|
|
SCL Pin
|
|
SDA Pin
|
|
PinMode PinMode
|
|
}
|
|
|
|
// I2CConfig is used to store config info for I2C.
|
|
type I2CConfig struct {
|
|
Frequency uint32
|
|
SCL Pin
|
|
SDA Pin
|
|
}
|
|
|
|
const (
|
|
// SERCOM_FREQ_REF is always reference frequency on SAMD51 regardless of CPU speed.
|
|
SERCOM_FREQ_REF = 48000000
|
|
|
|
// Default rise time in nanoseconds, based on 4.7K ohm pull up resistors
|
|
riseTimeNanoseconds = 125
|
|
|
|
// wire bus states
|
|
wireUnknownState = 0
|
|
wireIdleState = 1
|
|
wireOwnerState = 2
|
|
wireBusyState = 3
|
|
|
|
// wire commands
|
|
wireCmdNoAction = 0
|
|
wireCmdRepeatStart = 1
|
|
wireCmdRead = 2
|
|
wireCmdStop = 3
|
|
)
|
|
|
|
const i2cTimeout = 1000
|
|
|
|
// Configure is intended to setup the I2C interface.
|
|
func (i2c I2C) Configure(config I2CConfig) {
|
|
// Default I2C bus speed is 100 kHz.
|
|
if config.Frequency == 0 {
|
|
config.Frequency = TWI_FREQ_100KHZ
|
|
}
|
|
|
|
// reset SERCOM
|
|
i2c.Bus.CTRLA.SetBits(sam.SERCOM_I2CM_CTRLA_SWRST)
|
|
for i2c.Bus.CTRLA.HasBits(sam.SERCOM_I2CM_CTRLA_SWRST) ||
|
|
i2c.Bus.SYNCBUSY.HasBits(sam.SERCOM_I2CM_SYNCBUSY_SWRST) {
|
|
}
|
|
|
|
// Set i2c master mode
|
|
//SERCOM_I2CM_CTRLA_MODE( I2C_MASTER_OPERATION )
|
|
// sam.SERCOM_I2CM_CTRLA_MODE_I2C_MASTER = 5?
|
|
i2c.Bus.CTRLA.Set(5 << sam.SERCOM_I2CM_CTRLA_MODE_Pos) // |
|
|
|
|
i2c.SetBaudRate(config.Frequency)
|
|
|
|
// Enable I2CM port.
|
|
// sercom->USART.CTRLA.bit.ENABLE = 0x1u;
|
|
i2c.Bus.CTRLA.SetBits(sam.SERCOM_I2CM_CTRLA_ENABLE)
|
|
for i2c.Bus.SYNCBUSY.HasBits(sam.SERCOM_I2CM_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
// set bus idle mode
|
|
i2c.Bus.STATUS.SetBits(wireIdleState << sam.SERCOM_I2CM_STATUS_BUSSTATE_Pos)
|
|
for i2c.Bus.SYNCBUSY.HasBits(sam.SERCOM_I2CM_SYNCBUSY_SYSOP) {
|
|
}
|
|
|
|
// enable pins
|
|
i2c.SDA.Configure(PinConfig{Mode: i2c.PinMode})
|
|
i2c.SCL.Configure(PinConfig{Mode: i2c.PinMode})
|
|
}
|
|
|
|
// SetBaudRate sets the communication speed for the I2C.
|
|
func (i2c I2C) SetBaudRate(br uint32) {
|
|
// Synchronous arithmetic baudrate, via Adafruit SAMD51 implementation:
|
|
// sercom->I2CM.BAUD.bit.BAUD = SERCOM_FREQ_REF / ( 2 * baudrate) - 1 ;
|
|
baud := SERCOM_FREQ_REF/(2*br) - 1
|
|
i2c.Bus.BAUD.Set(baud)
|
|
}
|
|
|
|
// Tx does a single I2C transaction at the specified address.
|
|
// It clocks out the given address, writes the bytes in w, reads back len(r)
|
|
// bytes and stores them in r, and generates a stop condition on the bus.
|
|
func (i2c I2C) Tx(addr uint16, w, r []byte) error {
|
|
var err error
|
|
if len(w) != 0 {
|
|
// send start/address for write
|
|
i2c.sendAddress(addr, true)
|
|
|
|
// wait until transmission complete
|
|
timeout := i2cTimeout
|
|
for !i2c.Bus.INTFLAG.HasBits(sam.SERCOM_I2CM_INTFLAG_MB) {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return errors.New("I2C timeout on ready to write data")
|
|
}
|
|
}
|
|
|
|
// ACK received (0: ACK, 1: NACK)
|
|
if i2c.Bus.STATUS.HasBits(sam.SERCOM_I2CM_STATUS_RXNACK) {
|
|
return errors.New("I2C write error: expected ACK not NACK")
|
|
}
|
|
|
|
// write data
|
|
for _, b := range w {
|
|
err = i2c.WriteByte(b)
|
|
if err != nil {
|
|
return err
|
|
}
|
|
}
|
|
|
|
err = i2c.signalStop()
|
|
if err != nil {
|
|
return err
|
|
}
|
|
}
|
|
if len(r) != 0 {
|
|
// send start/address for read
|
|
i2c.sendAddress(addr, false)
|
|
|
|
// wait transmission complete
|
|
for !i2c.Bus.INTFLAG.HasBits(sam.SERCOM_I2CM_INTFLAG_SB) {
|
|
// If the slave NACKS the address, the MB bit will be set.
|
|
// In that case, send a stop condition and return error.
|
|
if i2c.Bus.INTFLAG.HasBits(sam.SERCOM_I2CM_INTFLAG_MB) {
|
|
i2c.Bus.CTRLB.SetBits(wireCmdStop << sam.SERCOM_I2CM_CTRLB_CMD_Pos) // Stop condition
|
|
return errors.New("I2C read error: expected ACK not NACK")
|
|
}
|
|
}
|
|
|
|
// ACK received (0: ACK, 1: NACK)
|
|
if i2c.Bus.STATUS.HasBits(sam.SERCOM_I2CM_STATUS_RXNACK) {
|
|
return errors.New("I2C read error: expected ACK not NACK")
|
|
}
|
|
|
|
// read first byte
|
|
r[0] = i2c.readByte()
|
|
for i := 1; i < len(r); i++ {
|
|
// Send an ACK
|
|
i2c.Bus.CTRLB.ClearBits(sam.SERCOM_I2CM_CTRLB_ACKACT)
|
|
|
|
i2c.signalRead()
|
|
|
|
// Read data and send the ACK
|
|
r[i] = i2c.readByte()
|
|
}
|
|
|
|
// Send NACK to end transmission
|
|
i2c.Bus.CTRLB.SetBits(sam.SERCOM_I2CM_CTRLB_ACKACT)
|
|
|
|
err = i2c.signalStop()
|
|
if err != nil {
|
|
return err
|
|
}
|
|
}
|
|
|
|
return nil
|
|
}
|
|
|
|
// WriteByte writes a single byte to the I2C bus.
|
|
func (i2c I2C) WriteByte(data byte) error {
|
|
// Send data byte
|
|
i2c.Bus.DATA.Set(data)
|
|
|
|
// wait until transmission successful
|
|
timeout := i2cTimeout
|
|
for !i2c.Bus.INTFLAG.HasBits(sam.SERCOM_I2CM_INTFLAG_MB) {
|
|
// check for bus error
|
|
if i2c.Bus.STATUS.HasBits(sam.SERCOM_I2CM_STATUS_BUSERR) {
|
|
return errors.New("I2C bus error")
|
|
}
|
|
timeout--
|
|
if timeout == 0 {
|
|
return errors.New("I2C timeout on write data")
|
|
}
|
|
}
|
|
|
|
if i2c.Bus.STATUS.HasBits(sam.SERCOM_I2CM_STATUS_RXNACK) {
|
|
return errors.New("I2C write error: expected ACK not NACK")
|
|
}
|
|
|
|
return nil
|
|
}
|
|
|
|
// sendAddress sends the address and start signal
|
|
func (i2c I2C) sendAddress(address uint16, write bool) error {
|
|
data := (address << 1)
|
|
if !write {
|
|
data |= 1 // set read flag
|
|
}
|
|
|
|
// wait until bus ready
|
|
timeout := i2cTimeout
|
|
for !i2c.Bus.STATUS.HasBits(wireIdleState<<sam.SERCOM_I2CM_STATUS_BUSSTATE_Pos) &&
|
|
!i2c.Bus.STATUS.HasBits(wireOwnerState<<sam.SERCOM_I2CM_STATUS_BUSSTATE_Pos) {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return errors.New("I2C timeout on bus ready")
|
|
}
|
|
}
|
|
i2c.Bus.ADDR.Set(uint32(data))
|
|
|
|
return nil
|
|
}
|
|
|
|
func (i2c I2C) signalStop() error {
|
|
i2c.Bus.CTRLB.SetBits(wireCmdStop << sam.SERCOM_I2CM_CTRLB_CMD_Pos) // Stop command
|
|
timeout := i2cTimeout
|
|
for i2c.Bus.SYNCBUSY.HasBits(sam.SERCOM_I2CM_SYNCBUSY_SYSOP) {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return errors.New("I2C timeout on signal stop")
|
|
}
|
|
}
|
|
return nil
|
|
}
|
|
|
|
func (i2c I2C) signalRead() error {
|
|
i2c.Bus.CTRLB.SetBits(wireCmdRead << sam.SERCOM_I2CM_CTRLB_CMD_Pos) // Read command
|
|
timeout := i2cTimeout
|
|
for i2c.Bus.SYNCBUSY.HasBits(sam.SERCOM_I2CM_SYNCBUSY_SYSOP) {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return errors.New("I2C timeout on signal read")
|
|
}
|
|
}
|
|
return nil
|
|
}
|
|
|
|
func (i2c I2C) readByte() byte {
|
|
for !i2c.Bus.INTFLAG.HasBits(sam.SERCOM_I2CM_INTFLAG_SB) {
|
|
}
|
|
return byte(i2c.Bus.DATA.Get())
|
|
}
|
|
|
|
// SPI
|
|
type SPI struct {
|
|
Bus *sam.SERCOM_SPIM_Type
|
|
SERCOM uint8
|
|
}
|
|
|
|
// SPIConfig is used to store config info for SPI.
|
|
type SPIConfig struct {
|
|
Frequency uint32
|
|
SCK Pin
|
|
MOSI Pin
|
|
MISO Pin
|
|
LSBFirst bool
|
|
Mode uint8
|
|
}
|
|
|
|
// Configure is intended to setup the SPI interface.
|
|
func (spi SPI) Configure(config SPIConfig) error {
|
|
// Use default pins if not set.
|
|
if config.SCK == 0 && config.MOSI == 0 && config.MISO == 0 {
|
|
config.SCK = SPI0_SCK_PIN
|
|
config.MOSI = SPI0_MOSI_PIN
|
|
config.MISO = SPI0_MISO_PIN
|
|
}
|
|
|
|
// set default frequency
|
|
if config.Frequency == 0 {
|
|
config.Frequency = 4000000
|
|
}
|
|
|
|
// Determine the input pinout (for MISO).
|
|
var dataInPinout uint32
|
|
misoPinMode, misoPad, ok := findPinPadMapping(spi.SERCOM, config.MISO)
|
|
if config.MISO != NoPin {
|
|
if !ok {
|
|
return ErrInvalidInputPin
|
|
}
|
|
dataInPinout = misoPad // mapped directly
|
|
}
|
|
|
|
// Determine the output pinout (for MOSI/SCK).
|
|
// See DOPO field in the CTRLA register on page 986 of the datasheet.
|
|
var dataOutPinout uint32
|
|
sckPinMode, sckPad, ok := findPinPadMapping(spi.SERCOM, config.SCK)
|
|
if !ok || sckPad != 1 {
|
|
// SCK pad must always be 1
|
|
return ErrInvalidOutputPin
|
|
}
|
|
mosiPinMode, mosiPad, ok := findPinPadMapping(spi.SERCOM, config.MOSI)
|
|
if !ok {
|
|
return ErrInvalidOutputPin
|
|
}
|
|
switch mosiPad {
|
|
case 0:
|
|
dataOutPinout = 0x0
|
|
case 3:
|
|
dataOutPinout = 0x2
|
|
default:
|
|
return ErrInvalidOutputPin
|
|
}
|
|
|
|
// Disable SPI port.
|
|
spi.Bus.CTRLA.ClearBits(sam.SERCOM_SPIM_CTRLA_ENABLE)
|
|
for spi.Bus.SYNCBUSY.HasBits(sam.SERCOM_SPIM_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
// enable pins
|
|
config.SCK.Configure(PinConfig{Mode: sckPinMode})
|
|
config.MOSI.Configure(PinConfig{Mode: mosiPinMode})
|
|
if config.MISO != NoPin {
|
|
config.MISO.Configure(PinConfig{Mode: misoPinMode})
|
|
}
|
|
|
|
// reset SERCOM
|
|
spi.Bus.CTRLA.SetBits(sam.SERCOM_SPIM_CTRLA_SWRST)
|
|
for spi.Bus.CTRLA.HasBits(sam.SERCOM_SPIM_CTRLA_SWRST) ||
|
|
spi.Bus.SYNCBUSY.HasBits(sam.SERCOM_SPIM_SYNCBUSY_SWRST) {
|
|
}
|
|
|
|
// set bit transfer order
|
|
dataOrder := uint32(0)
|
|
if config.LSBFirst {
|
|
dataOrder = 1
|
|
}
|
|
|
|
// Set SPI master
|
|
// SERCOM_SPIM_CTRLA_MODE_SPI_MASTER = 3
|
|
spi.Bus.CTRLA.Set((3 << sam.SERCOM_SPIM_CTRLA_MODE_Pos) |
|
|
(dataOutPinout << sam.SERCOM_SPIM_CTRLA_DOPO_Pos) |
|
|
(dataInPinout << sam.SERCOM_SPIM_CTRLA_DIPO_Pos) |
|
|
(dataOrder << sam.SERCOM_SPIM_CTRLA_DORD_Pos))
|
|
|
|
spi.Bus.CTRLB.SetBits((0 << sam.SERCOM_SPIM_CTRLB_CHSIZE_Pos) | // 8bit char size
|
|
sam.SERCOM_SPIM_CTRLB_RXEN) // receive enable
|
|
|
|
for spi.Bus.SYNCBUSY.HasBits(sam.SERCOM_SPIM_SYNCBUSY_CTRLB) {
|
|
}
|
|
|
|
// set mode
|
|
switch config.Mode {
|
|
case 0:
|
|
spi.Bus.CTRLA.ClearBits(sam.SERCOM_SPIM_CTRLA_CPHA)
|
|
spi.Bus.CTRLA.ClearBits(sam.SERCOM_SPIM_CTRLA_CPOL)
|
|
case 1:
|
|
spi.Bus.CTRLA.SetBits(sam.SERCOM_SPIM_CTRLA_CPHA)
|
|
spi.Bus.CTRLA.ClearBits(sam.SERCOM_SPIM_CTRLA_CPOL)
|
|
case 2:
|
|
spi.Bus.CTRLA.ClearBits(sam.SERCOM_SPIM_CTRLA_CPHA)
|
|
spi.Bus.CTRLA.SetBits(sam.SERCOM_SPIM_CTRLA_CPOL)
|
|
case 3:
|
|
spi.Bus.CTRLA.SetBits(sam.SERCOM_SPIM_CTRLA_CPHA | sam.SERCOM_SPIM_CTRLA_CPOL)
|
|
default: // to mode 0
|
|
spi.Bus.CTRLA.ClearBits(sam.SERCOM_SPIM_CTRLA_CPHA)
|
|
spi.Bus.CTRLA.ClearBits(sam.SERCOM_SPIM_CTRLA_CPOL)
|
|
}
|
|
|
|
// Set synch speed for SPI
|
|
baudRate := SERCOM_FREQ_REF / (2 * config.Frequency)
|
|
spi.Bus.BAUD.Set(uint8(baudRate))
|
|
|
|
// Enable SPI port.
|
|
spi.Bus.CTRLA.SetBits(sam.SERCOM_SPIM_CTRLA_ENABLE)
|
|
for spi.Bus.SYNCBUSY.HasBits(sam.SERCOM_SPIM_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
return nil
|
|
}
|
|
|
|
// Transfer writes/reads a single byte using the SPI interface.
|
|
func (spi SPI) Transfer(w byte) (byte, error) {
|
|
// write data
|
|
spi.Bus.DATA.Set(uint32(w))
|
|
|
|
// wait for receive
|
|
for !spi.Bus.INTFLAG.HasBits(sam.SERCOM_SPIM_INTFLAG_RXC) {
|
|
}
|
|
|
|
// return data
|
|
return byte(spi.Bus.DATA.Get()), nil
|
|
}
|
|
|
|
// PWM
|
|
const period = 0xFFFF
|
|
|
|
// Configure configures a PWM pin for output.
|
|
func (pwm PWM) Configure() {
|
|
// Set pin as output
|
|
sam.PORT.GROUP[0].DIRSET.Set(1 << uint8(pwm.Pin))
|
|
// Set pin to low
|
|
sam.PORT.GROUP[0].OUTCLR.Set(1 << uint8(pwm.Pin))
|
|
|
|
// Enable the port multiplexer for pin
|
|
pwm.setPinCfg(sam.PORT_GROUP_PINCFG_PMUXEN)
|
|
|
|
// Connect timer/mux to pin.
|
|
pwmConfig := pwm.getMux()
|
|
|
|
if pwm.Pin&1 > 0 {
|
|
// odd pin, so save the even pins
|
|
val := pwm.getPMux() & sam.PORT_GROUP_PMUX_PMUXE_Msk
|
|
pwm.setPMux(val | uint8(pwmConfig<<sam.PORT_GROUP_PMUX_PMUXO_Pos))
|
|
} else {
|
|
// even pin, so save the odd pins
|
|
val := pwm.getPMux() & sam.PORT_GROUP_PMUX_PMUXO_Msk
|
|
pwm.setPMux(val | uint8(pwmConfig<<sam.PORT_GROUP_PMUX_PMUXE_Pos))
|
|
}
|
|
|
|
// figure out which TCCX timer for this pin
|
|
timer := pwm.getTimer()
|
|
|
|
// disable timer
|
|
timer.CTRLA.ClearBits(sam.TCC_CTRLA_ENABLE)
|
|
// Wait for synchronization
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
// Set prescaler to 1/256
|
|
// TCCx->CTRLA.reg = TCC_CTRLA_PRESCALER_DIV256 | TCC_CTRLA_PRESCSYNC_GCLK;
|
|
timer.CTRLA.SetBits(sam.TCC_CTRLA_PRESCALER_DIV256 | sam.TCC_CTRLA_PRESCSYNC_GCLK)
|
|
|
|
// Use "Normal PWM" (single-slope PWM)
|
|
timer.WAVE.SetBits(sam.TCC_WAVE_WAVEGEN_NPWM)
|
|
// Wait for synchronization
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_WAVE) {
|
|
}
|
|
|
|
// while (TCCx->SYNCBUSY.bit.CC0 || TCCx->SYNCBUSY.bit.CC1);
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC0) ||
|
|
timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC1) {
|
|
}
|
|
|
|
// Set the initial value
|
|
// TCCx->CC[tcChannel].reg = (uint32_t) value;
|
|
pwm.setChannel(0)
|
|
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC0) ||
|
|
timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC1) {
|
|
}
|
|
|
|
// Set the period (the number to count to (TOP) before resetting timer)
|
|
//TCC0->PER.reg = period;
|
|
timer.PER.Set(period)
|
|
// Wait for synchronization
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_PER) {
|
|
}
|
|
|
|
// enable timer
|
|
timer.CTRLA.SetBits(sam.TCC_CTRLA_ENABLE)
|
|
// Wait for synchronization
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_ENABLE) {
|
|
}
|
|
}
|
|
|
|
// Set turns on the duty cycle for a PWM pin using the provided value.
|
|
func (pwm PWM) Set(value uint16) {
|
|
// figure out which TCCX timer for this pin
|
|
timer := pwm.getTimer()
|
|
|
|
// Wait for synchronization
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CTRLB) {
|
|
}
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC0) ||
|
|
timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC1) {
|
|
}
|
|
|
|
// TCCx->CCBUF[tcChannel].reg = (uint32_t) value;
|
|
pwm.setChannelBuffer(uint32(value))
|
|
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC0) ||
|
|
timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CC1) {
|
|
}
|
|
|
|
// TCCx->CTRLBCLR.bit.LUPD = 1;
|
|
timer.CTRLBCLR.SetBits(sam.TCC_CTRLBCLR_LUPD)
|
|
for timer.SYNCBUSY.HasBits(sam.TCC_SYNCBUSY_CTRLB) {
|
|
}
|
|
}
|
|
|
|
// getPMux returns the value for the correct PMUX register for this pin.
|
|
func (pwm PWM) getPMux() uint8 {
|
|
return pwm.Pin.getPMux()
|
|
}
|
|
|
|
// setPMux sets the value for the correct PMUX register for this pin.
|
|
func (pwm PWM) setPMux(val uint8) {
|
|
pwm.Pin.setPMux(val)
|
|
}
|
|
|
|
// getPinCfg returns the value for the correct PINCFG register for this pin.
|
|
func (pwm PWM) getPinCfg() uint8 {
|
|
return pwm.Pin.getPinCfg()
|
|
}
|
|
|
|
// setPinCfg sets the value for the correct PINCFG register for this pin.
|
|
func (pwm PWM) setPinCfg(val uint8) {
|
|
pwm.Pin.setPinCfg(val)
|
|
}
|
|
|
|
// setChannel sets the value for the correct channel for PWM on this pin
|
|
func (pwm PWM) setChannel(val uint32) {
|
|
switch pwm.Pin {
|
|
case PA16:
|
|
pwm.getTimer().CC[0].Set(val)
|
|
case PA17:
|
|
pwm.getTimer().CC[1].Set(val)
|
|
case PA14:
|
|
pwm.getTimer().CC[0].Set(val)
|
|
case PA15:
|
|
pwm.getTimer().CC[1].Set(val)
|
|
case PA18:
|
|
pwm.getTimer().CC[2].Set(val)
|
|
case PA19:
|
|
pwm.getTimer().CC[3].Set(val)
|
|
case PA20:
|
|
pwm.getTimer().CC[0].Set(val)
|
|
case PA21:
|
|
pwm.getTimer().CC[1].Set(val)
|
|
case PA23:
|
|
pwm.getTimer().CC[3].Set(val)
|
|
case PA22:
|
|
pwm.getTimer().CC[2].Set(val)
|
|
case PB31:
|
|
pwm.getTimer().CC[1].Set(val)
|
|
default:
|
|
return // not supported on this pin
|
|
}
|
|
}
|
|
|
|
// setChannelBuffer sets the value for the correct channel buffer for PWM on this pin
|
|
func (pwm PWM) setChannelBuffer(val uint32) {
|
|
switch pwm.Pin {
|
|
case PA16:
|
|
pwm.getTimer().CCBUF[0].Set(val)
|
|
case PA17:
|
|
pwm.getTimer().CCBUF[1].Set(val)
|
|
case PA14:
|
|
pwm.getTimer().CCBUF[0].Set(val)
|
|
case PA15:
|
|
pwm.getTimer().CCBUF[1].Set(val)
|
|
case PA18:
|
|
pwm.getTimer().CCBUF[2].Set(val)
|
|
case PA19:
|
|
pwm.getTimer().CCBUF[3].Set(val)
|
|
case PA20:
|
|
pwm.getTimer().CCBUF[0].Set(val)
|
|
case PA21:
|
|
pwm.getTimer().CCBUF[1].Set(val)
|
|
case PA23:
|
|
pwm.getTimer().CCBUF[3].Set(val)
|
|
case PA22:
|
|
pwm.getTimer().CCBUF[2].Set(val)
|
|
case PB31:
|
|
pwm.getTimer().CCBUF[1].Set(val)
|
|
default:
|
|
return // not supported on this pin
|
|
}
|
|
}
|
|
|
|
// getMux returns the pin mode mux to be used for PWM on this pin.
|
|
func (pwm PWM) getMux() PinMode {
|
|
switch pwm.Pin {
|
|
case PA16:
|
|
return PinPWMF
|
|
case PA17:
|
|
return PinPWMF
|
|
case PA14:
|
|
return PinPWMF
|
|
case PA15:
|
|
return PinPWMF
|
|
case PA18:
|
|
return PinPWMF
|
|
case PA19:
|
|
return PinPWMF
|
|
case PA20:
|
|
return PinPWMG
|
|
case PA21:
|
|
return PinPWMG
|
|
case PA23:
|
|
return PinPWMG
|
|
case PA22:
|
|
return PinPWMG
|
|
case PB31:
|
|
return PinPWMF
|
|
default:
|
|
return 0 // not supported on this pin
|
|
}
|
|
}
|
|
|
|
// USBCDC is the USB CDC aka serial over USB interface on the SAMD21.
|
|
type USBCDC struct {
|
|
Buffer *RingBuffer
|
|
}
|
|
|
|
// WriteByte writes a byte of data to the USB CDC interface.
|
|
func (usbcdc USBCDC) WriteByte(c byte) error {
|
|
// Supposedly to handle problem with Windows USB serial ports?
|
|
if usbLineInfo.lineState > 0 {
|
|
// set the data
|
|
udd_ep_in_cache_buffer[usb_CDC_ENDPOINT_IN][0] = c
|
|
|
|
usbEndpointDescriptors[usb_CDC_ENDPOINT_IN].DeviceDescBank[1].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_in_cache_buffer[usb_CDC_ENDPOINT_IN]))))
|
|
|
|
// clean multi packet size of bytes already sent
|
|
usbEndpointDescriptors[usb_CDC_ENDPOINT_IN].DeviceDescBank[1].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Mask << usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Pos)
|
|
|
|
// set count of bytes to be sent
|
|
usbEndpointDescriptors[usb_CDC_ENDPOINT_IN].DeviceDescBank[1].PCKSIZE.SetBits((1 & usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask) << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos)
|
|
|
|
// clear transfer complete flag
|
|
setEPINTFLAG(usb_CDC_ENDPOINT_IN, sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT1)
|
|
|
|
// send data by setting bank ready
|
|
setEPSTATUSSET(usb_CDC_ENDPOINT_IN, sam.USB_DEVICE_ENDPOINT_EPSTATUSSET_BK1RDY)
|
|
|
|
// wait for transfer to complete
|
|
timeout := 3000
|
|
for (getEPINTFLAG(usb_CDC_ENDPOINT_IN) & sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT1) == 0 {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return errors.New("USBCDC write byte timeout")
|
|
}
|
|
}
|
|
}
|
|
|
|
return nil
|
|
}
|
|
|
|
func (usbcdc USBCDC) DTR() bool {
|
|
return (usbLineInfo.lineState & usb_CDC_LINESTATE_DTR) > 0
|
|
}
|
|
|
|
func (usbcdc USBCDC) RTS() bool {
|
|
return (usbLineInfo.lineState & usb_CDC_LINESTATE_RTS) > 0
|
|
}
|
|
|
|
const (
|
|
// these are SAMD51 specific.
|
|
usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos = 0
|
|
usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask = 0x3FFF
|
|
|
|
usb_DEVICE_PCKSIZE_SIZE_Pos = 28
|
|
usb_DEVICE_PCKSIZE_SIZE_Mask = 0x7
|
|
|
|
usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Pos = 14
|
|
usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Mask = 0x3FFF
|
|
)
|
|
|
|
var (
|
|
usbEndpointDescriptors [8]usbDeviceDescriptor
|
|
|
|
udd_ep_in_cache_buffer [7][128]uint8
|
|
udd_ep_out_cache_buffer [7][128]uint8
|
|
|
|
isEndpointHalt = false
|
|
isRemoteWakeUpEnabled = false
|
|
endPoints = []uint32{usb_ENDPOINT_TYPE_CONTROL,
|
|
(usb_ENDPOINT_TYPE_INTERRUPT | usbEndpointIn),
|
|
(usb_ENDPOINT_TYPE_BULK | usbEndpointOut),
|
|
(usb_ENDPOINT_TYPE_BULK | usbEndpointIn)}
|
|
|
|
usbConfiguration uint8
|
|
usbSetInterface uint8
|
|
usbLineInfo = cdcLineInfo{115200, 0x00, 0x00, 0x08, 0x00}
|
|
)
|
|
|
|
// Configure the USB CDC interface. The config is here for compatibility with the UART interface.
|
|
func (usbcdc USBCDC) Configure(config UARTConfig) {
|
|
// reset USB interface
|
|
sam.USB_DEVICE.CTRLA.SetBits(sam.USB_DEVICE_CTRLA_SWRST)
|
|
for sam.USB_DEVICE.SYNCBUSY.HasBits(sam.USB_DEVICE_SYNCBUSY_SWRST) ||
|
|
sam.USB_DEVICE.SYNCBUSY.HasBits(sam.USB_DEVICE_SYNCBUSY_ENABLE) {
|
|
}
|
|
|
|
sam.USB_DEVICE.DESCADD.Set(uint32(uintptr(unsafe.Pointer(&usbEndpointDescriptors))))
|
|
|
|
// configure pins
|
|
USBCDC_DM_PIN.Configure(PinConfig{Mode: PinCom})
|
|
USBCDC_DP_PIN.Configure(PinConfig{Mode: PinCom})
|
|
|
|
// performs pad calibration from store fuses
|
|
handlePadCalibration()
|
|
|
|
// run in standby
|
|
sam.USB_DEVICE.CTRLA.SetBits(sam.USB_DEVICE_CTRLA_RUNSTDBY)
|
|
|
|
// set full speed
|
|
sam.USB_DEVICE.CTRLB.SetBits(sam.USB_DEVICE_CTRLB_SPDCONF_FS << sam.USB_DEVICE_CTRLB_SPDCONF_Pos)
|
|
|
|
// attach
|
|
sam.USB_DEVICE.CTRLB.ClearBits(sam.USB_DEVICE_CTRLB_DETACH)
|
|
|
|
// enable interrupt for end of reset
|
|
sam.USB_DEVICE.INTENSET.SetBits(sam.USB_DEVICE_INTENSET_EORST)
|
|
|
|
// enable interrupt for start of frame
|
|
sam.USB_DEVICE.INTENSET.SetBits(sam.USB_DEVICE_INTENSET_SOF)
|
|
|
|
// enable USB
|
|
sam.USB_DEVICE.CTRLA.SetBits(sam.USB_DEVICE_CTRLA_ENABLE)
|
|
|
|
// enable IRQ at highest priority
|
|
interrupt.New(sam.IRQ_USB_OTHER, handleUSBIRQ).Enable()
|
|
interrupt.New(sam.IRQ_USB_SOF_HSOF, handleUSBIRQ).Enable()
|
|
interrupt.New(sam.IRQ_USB_TRCPT0, handleUSBIRQ).Enable()
|
|
interrupt.New(sam.IRQ_USB_TRCPT1, handleUSBIRQ).Enable()
|
|
}
|
|
|
|
func handlePadCalibration() {
|
|
// Load Pad Calibration data from non-volatile memory
|
|
// This requires registers that are not included in the SVD file.
|
|
// Modeled after defines from samd21g18a.h and nvmctrl.h:
|
|
//
|
|
// #define NVMCTRL_OTP4 0x00806020
|
|
//
|
|
// #define USB_FUSES_TRANSN_ADDR (NVMCTRL_OTP4 + 4)
|
|
// #define USB_FUSES_TRANSN_Pos 13 /**< \brief (NVMCTRL_OTP4) USB pad Transn calibration */
|
|
// #define USB_FUSES_TRANSN_Msk (0x1Fu << USB_FUSES_TRANSN_Pos)
|
|
// #define USB_FUSES_TRANSN(value) ((USB_FUSES_TRANSN_Msk & ((value) << USB_FUSES_TRANSN_Pos)))
|
|
|
|
// #define USB_FUSES_TRANSP_ADDR (NVMCTRL_OTP4 + 4)
|
|
// #define USB_FUSES_TRANSP_Pos 18 /**< \brief (NVMCTRL_OTP4) USB pad Transp calibration */
|
|
// #define USB_FUSES_TRANSP_Msk (0x1Fu << USB_FUSES_TRANSP_Pos)
|
|
// #define USB_FUSES_TRANSP(value) ((USB_FUSES_TRANSP_Msk & ((value) << USB_FUSES_TRANSP_Pos)))
|
|
|
|
// #define USB_FUSES_TRIM_ADDR (NVMCTRL_OTP4 + 4)
|
|
// #define USB_FUSES_TRIM_Pos 23 /**< \brief (NVMCTRL_OTP4) USB pad Trim calibration */
|
|
// #define USB_FUSES_TRIM_Msk (0x7u << USB_FUSES_TRIM_Pos)
|
|
// #define USB_FUSES_TRIM(value) ((USB_FUSES_TRIM_Msk & ((value) << USB_FUSES_TRIM_Pos)))
|
|
//
|
|
fuse := *(*uint32)(unsafe.Pointer(uintptr(0x00806020) + 4))
|
|
calibTransN := uint16(fuse>>13) & uint16(0x1f)
|
|
calibTransP := uint16(fuse>>18) & uint16(0x1f)
|
|
calibTrim := uint16(fuse>>23) & uint16(0x7)
|
|
|
|
if calibTransN == 0x1f {
|
|
calibTransN = 5
|
|
}
|
|
sam.USB_DEVICE.PADCAL.SetBits(calibTransN << sam.USB_DEVICE_PADCAL_TRANSN_Pos)
|
|
|
|
if calibTransP == 0x1f {
|
|
calibTransP = 29
|
|
}
|
|
sam.USB_DEVICE.PADCAL.SetBits(calibTransP << sam.USB_DEVICE_PADCAL_TRANSP_Pos)
|
|
|
|
if calibTrim == 0x7 {
|
|
calibTransN = 3
|
|
}
|
|
sam.USB_DEVICE.PADCAL.SetBits(calibTrim << sam.USB_DEVICE_PADCAL_TRIM_Pos)
|
|
}
|
|
|
|
func handleUSBIRQ(interrupt.Interrupt) {
|
|
// reset all interrupt flags
|
|
flags := sam.USB_DEVICE.INTFLAG.Get()
|
|
sam.USB_DEVICE.INTFLAG.Set(flags)
|
|
|
|
// End of reset
|
|
if (flags & sam.USB_DEVICE_INTFLAG_EORST) > 0 {
|
|
// Configure control endpoint
|
|
initEndpoint(0, usb_ENDPOINT_TYPE_CONTROL)
|
|
|
|
// Enable Setup-Received interrupt
|
|
setEPINTENSET(0, sam.USB_DEVICE_ENDPOINT_EPINTENSET_RXSTP)
|
|
|
|
usbConfiguration = 0
|
|
|
|
// ack the End-Of-Reset interrupt
|
|
sam.USB_DEVICE.INTFLAG.Set(sam.USB_DEVICE_INTFLAG_EORST)
|
|
}
|
|
|
|
// Start of frame
|
|
if (flags & sam.USB_DEVICE_INTFLAG_SOF) > 0 {
|
|
// if you want to blink LED showing traffic, this would be the place...
|
|
}
|
|
|
|
// Endpoint 0 Setup interrupt
|
|
if getEPINTFLAG(0)&sam.USB_DEVICE_ENDPOINT_EPINTFLAG_RXSTP > 0 {
|
|
// ack setup received
|
|
setEPINTFLAG(0, sam.USB_DEVICE_ENDPOINT_EPINTFLAG_RXSTP)
|
|
|
|
// parse setup
|
|
setup := newUSBSetup(udd_ep_out_cache_buffer[0][:])
|
|
|
|
// Clear the Bank 0 ready flag on Control OUT
|
|
setEPSTATUSCLR(0, sam.USB_DEVICE_ENDPOINT_EPSTATUSCLR_BK0RDY)
|
|
usbEndpointDescriptors[0].DeviceDescBank[0].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos)
|
|
|
|
ok := false
|
|
if (setup.bmRequestType & usb_REQUEST_TYPE) == usb_REQUEST_STANDARD {
|
|
// Standard Requests
|
|
ok = handleStandardSetup(setup)
|
|
} else {
|
|
// Class Interface Requests
|
|
if setup.wIndex == usb_CDC_ACM_INTERFACE {
|
|
ok = cdcSetup(setup)
|
|
}
|
|
}
|
|
|
|
if ok {
|
|
// set Bank1 ready
|
|
setEPSTATUSSET(0, sam.USB_DEVICE_ENDPOINT_EPSTATUSSET_BK1RDY)
|
|
} else {
|
|
// Stall endpoint
|
|
setEPSTATUSSET(0, sam.USB_DEVICE_ENDPOINT_EPINTFLAG_STALL1)
|
|
}
|
|
|
|
if getEPINTFLAG(0)&sam.USB_DEVICE_ENDPOINT_EPINTFLAG_STALL1 > 0 {
|
|
// ack the stall
|
|
setEPINTFLAG(0, sam.USB_DEVICE_ENDPOINT_EPINTFLAG_STALL1)
|
|
|
|
// clear stall request
|
|
setEPINTENCLR(0, sam.USB_DEVICE_ENDPOINT_EPINTENCLR_STALL1)
|
|
}
|
|
}
|
|
|
|
// Now the actual transfer handlers, ignore endpoint number 0 (setup)
|
|
var i uint32
|
|
for i = 1; i < uint32(len(endPoints)); i++ {
|
|
// Check if endpoint has a pending interrupt
|
|
epFlags := getEPINTFLAG(i)
|
|
if (epFlags&sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT0) > 0 ||
|
|
(epFlags&sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT1) > 0 {
|
|
switch i {
|
|
case usb_CDC_ENDPOINT_OUT:
|
|
handleEndpoint(i)
|
|
setEPINTFLAG(i, epFlags)
|
|
case usb_CDC_ENDPOINT_IN, usb_CDC_ENDPOINT_ACM:
|
|
setEPSTATUSCLR(i, sam.USB_DEVICE_ENDPOINT_EPSTATUSCLR_BK1RDY)
|
|
setEPINTFLAG(i, sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT1)
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
func initEndpoint(ep, config uint32) {
|
|
switch config {
|
|
case usb_ENDPOINT_TYPE_INTERRUPT | usbEndpointIn:
|
|
// set packet size
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].PCKSIZE.SetBits(epPacketSize(64) << usb_DEVICE_PCKSIZE_SIZE_Pos)
|
|
|
|
// set data buffer address
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_in_cache_buffer[ep]))))
|
|
|
|
// set endpoint type
|
|
setEPCFG(ep, ((usb_ENDPOINT_TYPE_INTERRUPT + 1) << sam.USB_DEVICE_ENDPOINT_EPCFG_EPTYPE1_Pos))
|
|
|
|
case usb_ENDPOINT_TYPE_BULK | usbEndpointOut:
|
|
// set packet size
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.SetBits(epPacketSize(64) << usb_DEVICE_PCKSIZE_SIZE_Pos)
|
|
|
|
// set data buffer address
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_out_cache_buffer[ep]))))
|
|
|
|
// set endpoint type
|
|
setEPCFG(ep, ((usb_ENDPOINT_TYPE_BULK + 1) << sam.USB_DEVICE_ENDPOINT_EPCFG_EPTYPE0_Pos))
|
|
|
|
// receive interrupts when current transfer complete
|
|
setEPINTENSET(ep, sam.USB_DEVICE_ENDPOINT_EPINTENSET_TRCPT0)
|
|
|
|
// set byte count to zero, we have not received anything yet
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos)
|
|
|
|
// ready for next transfer
|
|
setEPSTATUSCLR(ep, sam.USB_DEVICE_ENDPOINT_EPSTATUSCLR_BK0RDY)
|
|
|
|
case usb_ENDPOINT_TYPE_INTERRUPT | usbEndpointOut:
|
|
// TODO: not really anything, seems like...
|
|
|
|
case usb_ENDPOINT_TYPE_BULK | usbEndpointIn:
|
|
// set packet size
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].PCKSIZE.SetBits(epPacketSize(64) << usb_DEVICE_PCKSIZE_SIZE_Pos)
|
|
|
|
// set data buffer address
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_in_cache_buffer[ep]))))
|
|
|
|
// set endpoint type
|
|
setEPCFG(ep, ((usb_ENDPOINT_TYPE_BULK + 1) << sam.USB_DEVICE_ENDPOINT_EPCFG_EPTYPE1_Pos))
|
|
|
|
// NAK on endpoint IN, the bank is not yet filled in.
|
|
setEPSTATUSCLR(ep, sam.USB_DEVICE_ENDPOINT_EPSTATUSCLR_BK1RDY)
|
|
|
|
case usb_ENDPOINT_TYPE_CONTROL:
|
|
// Control OUT
|
|
// set packet size
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.SetBits(epPacketSize(64) << usb_DEVICE_PCKSIZE_SIZE_Pos)
|
|
|
|
// set data buffer address
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_out_cache_buffer[ep]))))
|
|
|
|
// set endpoint type
|
|
setEPCFG(ep, getEPCFG(ep)|((usb_ENDPOINT_TYPE_CONTROL+1)<<sam.USB_DEVICE_ENDPOINT_EPCFG_EPTYPE0_Pos))
|
|
|
|
// Control IN
|
|
// set packet size
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].PCKSIZE.SetBits(epPacketSize(64) << usb_DEVICE_PCKSIZE_SIZE_Pos)
|
|
|
|
// set data buffer address
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_in_cache_buffer[ep]))))
|
|
|
|
// set endpoint type
|
|
setEPCFG(ep, getEPCFG(ep)|((usb_ENDPOINT_TYPE_CONTROL+1)<<sam.USB_DEVICE_ENDPOINT_EPCFG_EPTYPE1_Pos))
|
|
|
|
// Prepare OUT endpoint for receive
|
|
// set multi packet size for expected number of receive bytes on control OUT
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.SetBits(64 << usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Pos)
|
|
|
|
// set byte count to zero, we have not received anything yet
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos)
|
|
|
|
// NAK on endpoint OUT to show we are ready to receive control data
|
|
setEPSTATUSSET(ep, sam.USB_DEVICE_ENDPOINT_EPSTATUSSET_BK0RDY)
|
|
}
|
|
}
|
|
|
|
func handleStandardSetup(setup usbSetup) bool {
|
|
switch setup.bRequest {
|
|
case usb_GET_STATUS:
|
|
buf := []byte{0, 0}
|
|
|
|
if setup.bmRequestType != 0 { // endpoint
|
|
// TODO: actually check if the endpoint in question is currently halted
|
|
if isEndpointHalt {
|
|
buf[0] = 1
|
|
}
|
|
}
|
|
|
|
sendUSBPacket(0, buf)
|
|
return true
|
|
|
|
case usb_CLEAR_FEATURE:
|
|
if setup.wValueL == 1 { // DEVICEREMOTEWAKEUP
|
|
isRemoteWakeUpEnabled = false
|
|
} else if setup.wValueL == 0 { // ENDPOINTHALT
|
|
isEndpointHalt = false
|
|
}
|
|
sendZlp(0)
|
|
return true
|
|
|
|
case usb_SET_FEATURE:
|
|
if setup.wValueL == 1 { // DEVICEREMOTEWAKEUP
|
|
isRemoteWakeUpEnabled = true
|
|
} else if setup.wValueL == 0 { // ENDPOINTHALT
|
|
isEndpointHalt = true
|
|
}
|
|
sendZlp(0)
|
|
return true
|
|
|
|
case usb_SET_ADDRESS:
|
|
// set packet size 64 with auto Zlp after transfer
|
|
usbEndpointDescriptors[0].DeviceDescBank[1].PCKSIZE.Set((epPacketSize(64) << usb_DEVICE_PCKSIZE_SIZE_Pos) |
|
|
uint32(1<<31)) // autozlp
|
|
|
|
// ack the transfer is complete from the request
|
|
setEPINTFLAG(0, sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT1)
|
|
|
|
// set bank ready for data
|
|
setEPSTATUSSET(0, sam.USB_DEVICE_ENDPOINT_EPSTATUSSET_BK1RDY)
|
|
|
|
// wait for transfer to complete
|
|
timeout := 3000
|
|
for (getEPINTFLAG(0) & sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT1) == 0 {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return true
|
|
}
|
|
}
|
|
|
|
// last, set the device address to that requested by host
|
|
sam.USB_DEVICE.DADD.SetBits(setup.wValueL)
|
|
sam.USB_DEVICE.DADD.SetBits(sam.USB_DEVICE_DADD_ADDEN)
|
|
|
|
return true
|
|
|
|
case usb_GET_DESCRIPTOR:
|
|
sendDescriptor(setup)
|
|
return true
|
|
|
|
case usb_SET_DESCRIPTOR:
|
|
return false
|
|
|
|
case usb_GET_CONFIGURATION:
|
|
buff := []byte{usbConfiguration}
|
|
sendUSBPacket(0, buff)
|
|
return true
|
|
|
|
case usb_SET_CONFIGURATION:
|
|
if setup.bmRequestType&usb_REQUEST_RECIPIENT == usb_REQUEST_DEVICE {
|
|
for i := 1; i < len(endPoints); i++ {
|
|
initEndpoint(uint32(i), endPoints[i])
|
|
}
|
|
|
|
usbConfiguration = setup.wValueL
|
|
|
|
// Enable interrupt for CDC control messages from host (OUT packet)
|
|
setEPINTENSET(usb_CDC_ENDPOINT_ACM, sam.USB_DEVICE_ENDPOINT_EPINTENSET_TRCPT1)
|
|
|
|
// Enable interrupt for CDC data messages from host
|
|
setEPINTENSET(usb_CDC_ENDPOINT_OUT, sam.USB_DEVICE_ENDPOINT_EPINTENSET_TRCPT0)
|
|
|
|
sendZlp(0)
|
|
return true
|
|
} else {
|
|
return false
|
|
}
|
|
|
|
case usb_GET_INTERFACE:
|
|
buff := []byte{usbSetInterface}
|
|
sendUSBPacket(0, buff)
|
|
return true
|
|
|
|
case usb_SET_INTERFACE:
|
|
usbSetInterface = setup.wValueL
|
|
|
|
sendZlp(0)
|
|
return true
|
|
|
|
default:
|
|
return true
|
|
}
|
|
}
|
|
|
|
func cdcSetup(setup usbSetup) bool {
|
|
if setup.bmRequestType == usb_REQUEST_DEVICETOHOST_CLASS_INTERFACE {
|
|
if setup.bRequest == usb_CDC_GET_LINE_CODING {
|
|
b := make([]byte, 7)
|
|
b[0] = byte(usbLineInfo.dwDTERate)
|
|
b[1] = byte(usbLineInfo.dwDTERate >> 8)
|
|
b[2] = byte(usbLineInfo.dwDTERate >> 16)
|
|
b[3] = byte(usbLineInfo.dwDTERate >> 24)
|
|
b[4] = byte(usbLineInfo.bCharFormat)
|
|
b[5] = byte(usbLineInfo.bParityType)
|
|
b[6] = byte(usbLineInfo.bDataBits)
|
|
|
|
sendUSBPacket(0, b)
|
|
return true
|
|
}
|
|
}
|
|
|
|
if setup.bmRequestType == usb_REQUEST_HOSTTODEVICE_CLASS_INTERFACE {
|
|
if setup.bRequest == usb_CDC_SET_LINE_CODING {
|
|
b := receiveUSBControlPacket()
|
|
usbLineInfo.dwDTERate = uint32(b[0]) | uint32(b[1])<<8 | uint32(b[2])<<16 | uint32(b[3])<<24
|
|
usbLineInfo.bCharFormat = b[4]
|
|
usbLineInfo.bParityType = b[5]
|
|
usbLineInfo.bDataBits = b[6]
|
|
}
|
|
|
|
if setup.bRequest == usb_CDC_SET_CONTROL_LINE_STATE {
|
|
usbLineInfo.lineState = setup.wValueL
|
|
}
|
|
|
|
if setup.bRequest == usb_CDC_SET_LINE_CODING || setup.bRequest == usb_CDC_SET_CONTROL_LINE_STATE {
|
|
// auto-reset into the bootloader
|
|
if usbLineInfo.dwDTERate == 1200 && usbLineInfo.lineState&usb_CDC_LINESTATE_DTR == 0 {
|
|
ResetProcessor()
|
|
} else {
|
|
// TODO: cancel any reset
|
|
}
|
|
sendZlp(0)
|
|
}
|
|
|
|
if setup.bRequest == usb_CDC_SEND_BREAK {
|
|
// TODO: something with this value?
|
|
// breakValue = ((uint16_t)setup.wValueH << 8) | setup.wValueL;
|
|
// return false;
|
|
sendZlp(0)
|
|
}
|
|
return true
|
|
}
|
|
return false
|
|
}
|
|
|
|
func sendUSBPacket(ep uint32, data []byte) {
|
|
copy(udd_ep_in_cache_buffer[ep][:], data)
|
|
|
|
// Set endpoint address for sending data
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_in_cache_buffer[ep]))))
|
|
|
|
// clear multi-packet size which is total bytes already sent
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Mask << usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Pos)
|
|
|
|
// set byte count, which is total number of bytes to be sent
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].PCKSIZE.SetBits(uint32((len(data) & usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask) << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos))
|
|
}
|
|
|
|
func receiveUSBControlPacket() []byte {
|
|
// address
|
|
usbEndpointDescriptors[0].DeviceDescBank[0].ADDR.Set(uint32(uintptr(unsafe.Pointer(&udd_ep_out_cache_buffer[0]))))
|
|
|
|
// set byte count to zero
|
|
usbEndpointDescriptors[0].DeviceDescBank[0].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos)
|
|
|
|
// set ready for next data
|
|
setEPSTATUSCLR(0, sam.USB_DEVICE_ENDPOINT_EPSTATUSCLR_BK0RDY)
|
|
|
|
// Wait until OUT transfer is ready.
|
|
timeout := 300000
|
|
for (getEPSTATUS(0) & sam.USB_DEVICE_ENDPOINT_EPSTATUS_BK0RDY) == 0 {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return []byte{}
|
|
}
|
|
}
|
|
|
|
// Wait until OUT transfer is completed.
|
|
timeout = 300000
|
|
for (getEPINTFLAG(0) & sam.USB_DEVICE_ENDPOINT_EPINTFLAG_TRCPT1) == 0 {
|
|
timeout--
|
|
if timeout == 0 {
|
|
return []byte{}
|
|
}
|
|
}
|
|
|
|
// get data
|
|
bytesread := uint32((usbEndpointDescriptors[0].DeviceDescBank[0].PCKSIZE.Get() >>
|
|
usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos) & usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask)
|
|
|
|
data := make([]byte, bytesread)
|
|
copy(data, udd_ep_out_cache_buffer[0][:])
|
|
|
|
return data
|
|
}
|
|
|
|
// sendDescriptor creates and sends the various USB descriptor types that
|
|
// can be requested by the host.
|
|
func sendDescriptor(setup usbSetup) {
|
|
switch setup.wValueH {
|
|
case usb_CONFIGURATION_DESCRIPTOR_TYPE:
|
|
sendConfiguration(setup)
|
|
return
|
|
case usb_DEVICE_DESCRIPTOR_TYPE:
|
|
if setup.wLength == 8 {
|
|
// composite descriptor requested, so only send 8 bytes
|
|
dd := NewDeviceDescriptor(0xEF, 0x02, 0x01, 64, usb_VID, usb_PID, 0x100, usb_IMANUFACTURER, usb_IPRODUCT, usb_ISERIAL, 1)
|
|
sendUSBPacket(0, dd.Bytes()[:8])
|
|
} else {
|
|
// complete descriptor requested so send entire packet
|
|
dd := NewDeviceDescriptor(0x00, 0x00, 0x00, 64, usb_VID, usb_PID, 0x100, usb_IMANUFACTURER, usb_IPRODUCT, usb_ISERIAL, 1)
|
|
sendUSBPacket(0, dd.Bytes())
|
|
}
|
|
return
|
|
|
|
case usb_STRING_DESCRIPTOR_TYPE:
|
|
switch setup.wValueL {
|
|
case 0:
|
|
b := make([]byte, 4)
|
|
b[0] = byte(usb_STRING_LANGUAGE[0] >> 8)
|
|
b[1] = byte(usb_STRING_LANGUAGE[0] & 0xff)
|
|
b[2] = byte(usb_STRING_LANGUAGE[1] >> 8)
|
|
b[3] = byte(usb_STRING_LANGUAGE[1] & 0xff)
|
|
sendUSBPacket(0, b)
|
|
|
|
case usb_IPRODUCT:
|
|
prod := []byte(usb_STRING_PRODUCT)
|
|
b := make([]byte, len(prod)*2+2)
|
|
b[0] = byte(len(prod)*2 + 2)
|
|
b[1] = 0x03
|
|
|
|
for i, val := range prod {
|
|
b[i*2] = 0
|
|
b[i*2+1] = val
|
|
}
|
|
|
|
sendUSBPacket(0, b)
|
|
|
|
case usb_IMANUFACTURER:
|
|
prod := []byte(usb_STRING_MANUFACTURER)
|
|
b := make([]byte, len(prod)*2+2)
|
|
b[0] = byte(len(prod)*2 + 2)
|
|
b[1] = 0x03
|
|
|
|
for i, val := range prod {
|
|
b[i*2] = 0
|
|
b[i*2+1] = val
|
|
}
|
|
|
|
sendUSBPacket(0, b)
|
|
|
|
case usb_ISERIAL:
|
|
// TODO: allow returning a product serial number
|
|
sendZlp(0)
|
|
}
|
|
|
|
// send final zero length packet and return
|
|
sendZlp(0)
|
|
return
|
|
}
|
|
|
|
// do not know how to handle this message, so return zero
|
|
sendZlp(0)
|
|
return
|
|
}
|
|
|
|
// sendConfiguration creates and sends the configuration packet to the host.
|
|
func sendConfiguration(setup usbSetup) {
|
|
if setup.wLength == 9 {
|
|
sz := uint16(configDescriptorSize + cdcSize)
|
|
config := NewConfigDescriptor(sz, 2)
|
|
sendUSBPacket(0, config.Bytes())
|
|
} else {
|
|
iad := NewIADDescriptor(0, 2, usb_CDC_COMMUNICATION_INTERFACE_CLASS, usb_CDC_ABSTRACT_CONTROL_MODEL, 0)
|
|
|
|
cif := NewInterfaceDescriptor(usb_CDC_ACM_INTERFACE, 1, usb_CDC_COMMUNICATION_INTERFACE_CLASS, usb_CDC_ABSTRACT_CONTROL_MODEL, 0)
|
|
|
|
header := NewCDCCSInterfaceDescriptor(usb_CDC_HEADER, usb_CDC_V1_10&0xFF, (usb_CDC_V1_10>>8)&0x0FF)
|
|
|
|
controlManagement := NewACMFunctionalDescriptor(usb_CDC_ABSTRACT_CONTROL_MANAGEMENT, 6)
|
|
|
|
functionalDescriptor := NewCDCCSInterfaceDescriptor(usb_CDC_UNION, usb_CDC_ACM_INTERFACE, usb_CDC_DATA_INTERFACE)
|
|
|
|
callManagement := NewCMFunctionalDescriptor(usb_CDC_CALL_MANAGEMENT, 1, 1)
|
|
|
|
cifin := NewEndpointDescriptor((usb_CDC_ENDPOINT_ACM | usbEndpointIn), usb_ENDPOINT_TYPE_INTERRUPT, 0x10, 0x10)
|
|
|
|
dif := NewInterfaceDescriptor(usb_CDC_DATA_INTERFACE, 2, usb_CDC_DATA_INTERFACE_CLASS, 0, 0)
|
|
|
|
out := NewEndpointDescriptor((usb_CDC_ENDPOINT_OUT | usbEndpointOut), usb_ENDPOINT_TYPE_BULK, usbEndpointPacketSize, 0)
|
|
|
|
in := NewEndpointDescriptor((usb_CDC_ENDPOINT_IN | usbEndpointIn), usb_ENDPOINT_TYPE_BULK, usbEndpointPacketSize, 0)
|
|
|
|
cdc := NewCDCDescriptor(iad,
|
|
cif,
|
|
header,
|
|
controlManagement,
|
|
functionalDescriptor,
|
|
callManagement,
|
|
cifin,
|
|
dif,
|
|
out,
|
|
in)
|
|
|
|
sz := uint16(configDescriptorSize + cdcSize)
|
|
config := NewConfigDescriptor(sz, 2)
|
|
|
|
buf := make([]byte, 0)
|
|
buf = append(buf, config.Bytes()...)
|
|
buf = append(buf, cdc.Bytes()...)
|
|
|
|
sendUSBPacket(0, buf)
|
|
}
|
|
}
|
|
|
|
func handleEndpoint(ep uint32) {
|
|
// get data
|
|
count := int((usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.Get() >>
|
|
usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos) & usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask)
|
|
|
|
// move to ring buffer
|
|
for i := 0; i < count; i++ {
|
|
UART0.Receive(byte((udd_ep_out_cache_buffer[ep][i] & 0xFF)))
|
|
}
|
|
|
|
// set byte count to zero
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos)
|
|
|
|
// set multi packet size to 64
|
|
usbEndpointDescriptors[ep].DeviceDescBank[0].PCKSIZE.SetBits(64 << usb_DEVICE_PCKSIZE_MULTI_PACKET_SIZE_Pos)
|
|
|
|
// set ready for next data
|
|
setEPSTATUSCLR(ep, sam.USB_DEVICE_ENDPOINT_EPSTATUSCLR_BK0RDY)
|
|
}
|
|
|
|
func sendZlp(ep uint32) {
|
|
usbEndpointDescriptors[ep].DeviceDescBank[1].PCKSIZE.ClearBits(usb_DEVICE_PCKSIZE_BYTE_COUNT_Mask << usb_DEVICE_PCKSIZE_BYTE_COUNT_Pos)
|
|
}
|
|
|
|
func epPacketSize(size uint16) uint32 {
|
|
switch size {
|
|
case 8:
|
|
return 0
|
|
case 16:
|
|
return 1
|
|
case 32:
|
|
return 2
|
|
case 64:
|
|
return 3
|
|
case 128:
|
|
return 4
|
|
case 256:
|
|
return 5
|
|
case 512:
|
|
return 6
|
|
case 1023:
|
|
return 7
|
|
default:
|
|
return 0
|
|
}
|
|
}
|
|
|
|
func getEPCFG(ep uint32) uint8 {
|
|
return sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPCFG.Get()
|
|
}
|
|
|
|
func setEPCFG(ep uint32, val uint8) {
|
|
sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPCFG.Set(val)
|
|
}
|
|
|
|
func setEPSTATUSCLR(ep uint32, val uint8) {
|
|
sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPSTATUSCLR.Set(val)
|
|
}
|
|
|
|
func setEPSTATUSSET(ep uint32, val uint8) {
|
|
sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPSTATUSSET.Set(val)
|
|
}
|
|
|
|
func getEPSTATUS(ep uint32) uint8 {
|
|
return sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPSTATUS.Get()
|
|
}
|
|
|
|
func getEPINTFLAG(ep uint32) uint8 {
|
|
return sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPINTFLAG.Get()
|
|
}
|
|
|
|
func setEPINTFLAG(ep uint32, val uint8) {
|
|
sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPINTFLAG.Set(val)
|
|
}
|
|
|
|
func setEPINTENCLR(ep uint32, val uint8) {
|
|
sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPINTENCLR.Set(val)
|
|
}
|
|
|
|
func setEPINTENSET(ep uint32, val uint8) {
|
|
sam.USB_DEVICE.DEVICE_ENDPOINT[ep].EPINTENSET.Set(val)
|
|
}
|
|
|
|
// ResetProcessor should perform a system reset in preparation
|
|
// to switch to the bootloader to flash new firmware.
|
|
func ResetProcessor() {
|
|
arm.DisableInterrupts()
|
|
|
|
// Perform magic reset into bootloader, as mentioned in
|
|
// https://github.com/arduino/ArduinoCore-samd/issues/197
|
|
*(*uint32)(unsafe.Pointer(uintptr(0x20000000 + HSRAM_SIZE - 4))) = RESET_MAGIC_VALUE
|
|
|
|
arm.SystemReset()
|
|
}
|